Pioneer SUPER TUNER III D FH-P4200MP Manuale di installazione

Sfoglia online o scarica il pdf Manuale di installazione per Ricevitore per auto Pioneer SUPER TUNER III D FH-P4200MP. Pioneer SUPER TUNER III D FH-P4200MP 4. Owner's manual
Anche per Pioneer SUPER TUNER III D FH-P4200MP: Manuale d'uso (34 pagine)

Stampa la pagina

FH-P4200MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit

est conforme à CEMA.

Printed in China

Imprimé en Chine

<YRD5034-A/U> UC

Connecting the Units

Note:

• When an external power amp is being used with

• This unit is for vehicles with a 12-volt battery and

this system, be sure not to connect the blue/white

negative grounding. Before installing it in a recre-

lead to the amp's power terminal. Likewise, do

ational vehicle, truck or bus, check the battery

voltage.

not connect the blue/white lead to the power ter-

• To avoid shorts in the electrical system, be sure to

minal of the auto-antenna. Such connection could

disconnect the ≠ battery cable before beginning

cause excessive current drain and malfunction.

installation.

• To avoid a short-circuit, cover the disconnected

• Refer to the owner's manual for details on

lead with insulating tape. Insulate the unused

connecting the power amp and other units, then

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

make connections correctly.

• To prevent incorrect connection, the input side of

• Secure the wiring with cable clamps or adhesive

the IP-BUS connector is blue, and the output side

tape. To protect the wiring, wrap adhesive tape

is black. Connect the connectors of the same

around them where they lie against metal parts.

colors correctly.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake,

• This unit can not be installed in a vehicle that

and seat rails. Do not route wiring in places that

does not have an ACC (accessory) position on

get hot, such as near the heater outlet. If the insu-

the ignition switch. (Fig. 1)

lation of the wiring melts or gets torn, there is a

danger of the wiring short-circuiting to the vehicle

body.

• Don't pass the yellow lead through a hole into the

engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

ACC position

No ACC position

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a

• The black lead is ground. Please ground this lead

fuse of the rating prescribed on this unit.

separately from the ground of high-current prod-

• Since a unique BPTL circuit is employed, never

ucts such as power amps.

wire so the speaker leads are directly grounded or

If you ground the products together and the

the left and right ≠ speaker leads are common.

ground becomes detached, there is a risk of dam-

• If the RCA pin jack on the unit will not be used,

age to the products or fire.

do not remove the caps attached to the end of the

connector.

• Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

ance of 4 to 8 ohms. Connecting speakers with

output and/or impedance values other than those

noted here may result in the speakers catching

• Cords for this product and those for other prod-

fire, emitting smoke or becoming damaged.

ucts may be different colors even if they have the

• When this product's source is switched ON, a

same function. When connecting this product to

control signal is output through the blue/white

another product, refer to the supplied manuals of

lead. Connect to an external power amp's system

both products and connect cords that have the

remote control or the car's Auto-antenna relay

same function.

control terminal (max. 300 mA 12 V DC). If the

car features a glass antenna, connect to the anten-

na booster power supply terminal.

15 cm (5-7/8 in.)

Front output

(FRONT OUTPUT)

Subwoofer output or nonfading output

Antenna jack

This Product

IP-BUS input (Blue)

Yellow/black

If you use an equipment with Mute function, wire this lead

to the Audio Mute lead on that equipment. If not, keep the

Audio Mute lead free of any connections.

Fig. 1

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

With a 2 speaker system, do not connect

To vehicle (metal) body.

anything to the speaker leads that are not

This terminal may or

connected to speakers.

may not be included.

Perform these connections when using

the optional amplifier.

Connecting cords

with RCA pin plugs

(sold separately)

Fuse

IP-BUS cable

Multi-CD player

(sold separately)

System remote control

Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Front speaker

≠

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Subwoofer or

Rear speaker

≠

Power

(sold separately)

Power amp

(sold separately)

Front speaker

≠

Front speaker

≠

Right

Rear speaker

≠

Subwoofer or

Rear speaker

≠

Fig. 2