Pioneer XV-DV535 Impostazione

Sfoglia online o scarica il pdf Impostazione per Ricevitore Pioneer XV-DV535. Pioneer XV-DV535 2. Dvd/cd receiver
Anche per Pioneer XV-DV535: Impostazione (2 pagine)

Setting up your XV-DV535 DVD/CD Receiver
When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON or POWER button, and disconnect the power cord and AC adaptor from the AC outlet.
Do not use these speakers with any other system or amplifier as this may result in damage or fire. Before setting up, please read Important notes and safety precautions below for more information.
Check that you have all the accessories, then put
1
the batteries in the remote control.
Wireless speaker
• Wireless speaker (1)
• Transmitter (1)
system:
• AC adaptor (1)
• 2-pin RCA cord (1)
• Power cord (1)
Satellite speaker
• Center (1)
• Large non-skid pads
system:
• Front (x2)
Taiwan model (x4)
• Subwoofer (1)
All other models (x6)
• Speaker cables (x4)
• Mounting brackets ( x2 )
• Small non-skid pads (x12)
• Screws (for mounting
brackets) ( x2 )
*
Please refer to Wall-mounting the front speaker system
in the operating instructions for installation.
Batteries
CD
and remote
DVD
WIRELESS
control
Power cord *
FM antenna
4
* Illustration shows
DVD MENU
the Taiwan model
MUTE
Video cord
CH
Microphone
(for Auto MCACC setup)
AM loop antenna
3
1
2
4
Attach the smaller non-skid pads to the
base
of each of the front and center
The four (Taiwan model)/six (All
speakers.
other models) large non-skid pads are for
the subwoofer (as shown).
Use the supplied adhesive to attach 4 pads to the base of
each speakers and 4 (Taiwan model)/6 (All other models)
pads to the base of the subwoofer.
Taiwan model only – The subwoofer supplied with this
system can be placed upright or on its side (flat). Choose
the position that works best for your room, then attach the
large non-skid pads as shown.
Front speakers
Center speaker
Subwoofer
Taiwan model
All other models
Upright position Flat position
: Non-skid pads
Using the digital wireless speaker system
The wireless speaker system can be used for multichannel sound with your main setup, or as a second stereo speaker system.
CHANNEL indicator
1
Lights to indicate the selected channel.
2
CHANNEL
Press to select a frequency channel. The frequency channel changes sequentially each time the button is
pressed:
CH 4
CH 1
CH 2
CH 3
Transmitter antenna
3
Transmits signals to the wireless speaker.
Power cord
4
Connect to an AC outlet after connecting to the rear AC IN inlet.
TUNED indicator
5
Lights when the signal from the transmitter is properly received.
6
POWER indicator
Lights when the wireless speaker is switched on.
POWER
7
Press to switch the wireless speaker on or off.
• The wireless speaker has an internal antenna.
Overhead view of a multichannel (SURROUND) setup with the wireless speaker
Transmitter/
XV-DV535
CHANNEL
Front left
0 OPEN/CLOSE
6
DVD/CD
7
FM/AM
VOL.
+
STANDBY/ON
Center
Wireless speaker
AC IN
For the best surround sound, setup your speakers as above.
The front left and right speakers should be about 1.8–2.7 m apart.
2
Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.
Pull off the protective shields
1
of both AM antenna wires.
2
Push open the tabs, then insert
one wire fully into each terminal.
*
3
Release the tabs to secure the AM
*
antenna wires.
4
Fix the AM loop antenna to the
STANDBY/ON
FM/AM
L1/L2
attached stand.
TUNER
TV
LINE
OPEN CLOSE
8
0
To fix the stand to the antenna, bend in the
1
3
¡
direction indicated by the arrow (fig. A) then
4
7
RETURN
clip the loop onto the stand (fig. B).
TUNE+
ST–
ST+
ENTER
BASS
TUNE–
MODE
Note: If you plan to mount the AM antenna
MASTER
VOLUME
to a wall or other surface, secure the stand
TV CONTROL
with screws (fig. C) before clipping the loop
INPUT
VOL
to the stand. Make sure the reception is clear.
OPEN
5
Place the AM antenna on a flat
surface and point in the direction
giving the best reception.
Don't let it come into contact with metal
objects and avoid placing near computers,
television sets or other electrical appliances.
5
Connect each speaker using the color-coded speaker cords.
Match them to the colored speaker terminals on the rear
panel of the DVD/CD receiver.
* Illustration shows
IN
IN
OUT
OUT
MCACC
6
6
MIC
L
FRONT
CENTER
SPEAKERS
6
L
L
R
WIRELESS
TV AUDIO
LINE 1
6
R
R
6
6
SURROUND
SUB
WOOFER
Subwoofer (Purple)
Center (Green)
These speaker terminals can be hazardous when live. When you connect or
disconnect the speaker cables, to prevent the risk of electric shock, do not
touch uninsulated parts before disconnecting the power cord.
Transmitter
Wireless speaker
* Illustration shows
the Taiwan model
Subwoofer
Front right
• Do not leave the power cord near heating equipment. The coating of the cord may melt, which could
to AC outlet
lead to fire and/or electrocution.
• Make sure to grasp the body of the AC adaptor when removing it from the AC outlet. If you pull the
power cord, it may become damaged which could lead to fire and/or electrocution.
• Do not attempt to plug in or remove the AC adaptor with wet hands. This may result in electrocution.
• Insert the prongs of the AC adaptor all the way into the AC outlet. If the connection is incomplete, heat
may be generated which could lead to fire. Furthermore, contact with the connected prongs of the adaptor
may result in electrocution.
• Do not insert the AC adaptor into a AC outlet where the connection remains loose despite inserting
the prongs all the way into the outlet. Heat may be generated which could lead to fire. Consult with the
retailer or an electrician regarding replacement of the AC outlet.
fig. A
fig. B
4
6
1
2
ANTENNA
FM
AM
UNBAL 75Ω
LOOP ANTENNA
6
Connect the FM wire antenna to the FM UNBAL 75Ω antenna terminal.
For best results, extend the FM antenna fully and fix to a wall or door
frame. Don't drape loosely or leave coiled up.
The signal earth (H) is designed to reduce noise that occurs when an
Note:
antenna is connected. It is not an electrical safety earth.
Connect each speaker as shown below.
Color-coded wire
(Connect to speaker)
Color-coded connector
(Connect to rear panel)
the Taiwan model
Twist and pull off the protective
1
shields on each wire.
2
Connect the wires to the
speaker. Match the colored
wire with the color-coded
label (above the tabs), then
insert the colored wire into
the red (+) tab and the other
wire with the black (–) tab.
3
Connect the other end to the color-
coded speaker terminals on the
rear of the DVD/CD receiver (as
shown at left). Make sure to insert
Front left
completely.
(White)
Upper three terminals
The small lug at the wire-end of the
speaker plug should face up or
down depending on whether it's
being plugged into one of the
upper or lower three speaker
terminals. Please make sure to
connect correctly.
Lower three terminals
CHANNEL
1
2
3
4
1
2
3
*
4
5
6
TUNED
POWER
OFF
ON
TUNED
POWER
OFF
ON
* Illustration shows the Taiwan model
AC adaptor and power cord caution
3
Connect the WIRELESS (IN) jack on the transmitter to the
WIRELESS (OUT) jack on the rear panel of the DVD/CD
receiver using a 2-pin RCA cord, then connect to AC outlet
using the supplied AC adaptor.
fig. C
Transmitter
3
IN
IN
OUT
OUT
L
R
TV AUDIO
WIRELESS
LINE 1
XV-DV535 DVD/CD Receiver
When connecting, make sure both units are switched off and unplugged.
6
Connect the DVD/CD receiver to your TV, then connect the
supplied power cords.
Connect one end to a video input on your TV.
1
Use the supplied video cord.
2
Connect the other end to the video output of the DVD/CD receiver.
This player is equipped with copy protection technology. Do not connect this
player to your TV via a VCR using AV cables, as the picture from this player will not
appear properly on your TV.
3
Connect the power cords.
Connect both the wireless speaker and DVD/CD receiver power cords to their
respective AC IN inlets (the DVD/CD receiver hookup is shown in the illustration)
then plug them into an AC outlet.
IN
IN
OUT
OUT
L
R
TV AUDIO
WIRELESS
LINE 1
AC IN
* Illustration shows
the Taiwan model
Congratulations! You're done setting up.
Important notes and safety precautions
Using the remote control
The remote control can be used within a range of about 7 meters from the remote sensor on the front panel, and within a 30
degree angle.
Precautions:
• The remote control may not work if there is an obstacle between the remote control and the display unit, or if the remote control
is not directed towards the remote sensor of the display unit at the correct angle.
• The remote control may not work properly if strong light such as direct sunlight or fluorescent light is shining onto the unit's
remote sensor.
• The remote control may not work properly when this unit is used near devices emitting infrared rays, or when remote controls of
other devices which use infrared rays are used. Also, the use of this remote control may cause other devices to work improperly.
• When the operating range of the remote becomes too short, replace the batteries.
Remote control battery caution
Incorrect use of batteries may cause leakage or rupture.
Always be sure to follow these guidelines:
• Always insert batteries into the battery compartment correctly matching the positive ª and negative · polarities, as shown by
the display inside the compartment.
• Never mix new and used batteries.
• Batteries of the same size may have different voltages, depending on brand. Do not mix different brands of batteries.
• When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules that
apply in your country or area.
• In order to prevent battery leakage, remove the batteries when not using the remote control for an extended period (one month
or more). If leakage occurs, carefully wipe away any battery fluid inside the compartment, and replace the batteries with new ones.
• Do not allow books or other objects to rest on top of the remote control, since the buttons may be depressed, causing faster
7
exhaustion of the batteries.
Additional notes on connecting antennas
• Keep antenna cables away from the main unit and other cables.
• To assure optimum reception, pull the FM antenna so that it is fully extended and not coiled or hanging at the rear of the unit.
• If reception with the supplied antenna is poor, see the Other connections section in the main operating instructions for details on
connecting outdoor antennas.
Additional notes on speaker placement
Place speakers as shown at left to achieve the optimum surround sound effect
• Install the main front left and right speakers at an equal distance from the TV.
• The front and center speakers supplied with this system are magnetically shielded. However, depending on the installation
location, color distortion may occur if the speaker is installed extremely close to the screen of a television set. If this happens
case, turn the power switch of the television set OFF, and turn it ON after 15 to 30 minutes. If the problem persists, place the
speaker system away from the television set.
• Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.
• When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the
speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or damaging the speaker.
• Do not connect the supplied speakers with any other amplifier. This may result in malfunction or fire.
• The wirerless speaker and subwoofer are not magnetically shielded and so should not be placed near a TV or monitor.
Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to the wirerless
speaker or subwoofer.
• Do not fix the subwoofer and center speaker to the wall or ceiling; they could cause injury if they fell.
Placing the wireless speaker
• For best surround sound, make sure to place the wireless speaker directly behind the center of the
listening position and no higher than ear level. Also, make sure you don't move the wireless speaker
too far behind the listening position or you will lose much of the surround sound effect.
• For a greater surround sound effect from the wireless speaker, see Setting the channel levels on page
23 of the XV-DV535 main operating instructions to increase the surround channel levels.
• If your listening area is not large enough to place the wireless speaker behind you, you can use the
left and right placement options illustrated below with the Left and Right wireless modes. See Using
the wireless speaker system on page 10 of the XV-DV535 main operating instructions for more on the
wireless speaker modes.
Front left
Center
Subwoofer
Wireless
Listening position
speaker
• The wireless speaker can be used at distances up to 10m from the transmitter. This range may
change depending on the environment.
• Depending on your room characteristics, there will be places where you will achieve better
reception from the transmitter. If you are experiencing bad reception, try moving the transmitter or
the wireless speaker slightly. If the problem persists, try locating the best frequency channel with
the two units quite close together at first.
AC
R
L
IN
adaptor
WIRELESS
To AC outlet
OPTICAL IN
IN
AUDIO
CONTROL
LINE 2
FM
AM
ANTENNA
UNBAL 75Ω
LOOP ANTENNA
COMPONENT
VIDEO OUT
Y
P
B
AC IN
P
VIDEO
R
S-VIDEO
OUT
OUT
VIDEO
* Illustration shows the Taiwan model
VIDEO IN
OPTICAL IN
IN
AUDIO
CONTROL
LINE 2
FM
AM
ANTENNA
UNBAL 75Ω
LOOP ANTENNA
COMPONENT
VIDEO OUT
Y
P
B
VIDEO
P
OUT
VIDEO
R
S-VIDEO
VIDEO
OUT
OUT
VIDEO
AC IN
To AC outlet
Printed in
<XRE3106-A>
Front right
Front left
Center
Front right
Subwoofer
Wireless
Listening position
speaker