Pioneer VSX-9500S VSX-7500S Manuale di istruzioni per l'uso - Pagina 23
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Ricevitore stereo Pioneer VSX-9500S VSX-7500S. Pioneer VSX-9500S VSX-7500S 48.
Anche per Pioneer VSX-9500S VSX-7500S: Manuale di istruzioni per l'uso (48 pagine)
Stampa la pagina
REAR PANEL FACILITIES
@ FM/AM ANTENNA terminals
Use these antenna
terminals for reception of normal
FM and AM
broadcasts.
Attach the accessory AM Loop and FM T-type antennas, here.
* For details regarding antenna connection, see the section 'Hints for
Better Reception' on page 45.
(2) GND terminal
Cannect
the turntable ground lead to this terminal.
(3) CONTROL IN, OUT jacks
Used for system control with other Pioneer components
beuring the
BQ mark.
IN.......
For connection
from the CONTROL
OUT
jack of another
component.
OUT....
For connection to the CONTROL
IN jack of another compenent.
NOTE:
The receiver's remote sensor does not function when a plug fs inserted
in the IN jack,
To operate, point the remote cantro/ unit at the remete
sensor on the component to which the receiver's IN jack is connected.
pases
'contact
| '@ oe
To the CONTROL
IN jack of the Pioneer
=
component
bearing
the qj mark
Pioneer component
bearing the {ij mark.
Remote contro! unit
SURROUND
INPUT
BALANCE
control
(DOLBY
SURROUND}
[VSX-75008}
This knob is for adjusting the balance of the DOLBY SURROUND input
signal. To adjust, apply a monaural sound signa! and rotate until the
SURROUND
{rear} sound becomes minimal.
(See page 31.)
[VSX-2500S]
Set the front pane! PRO LOGIC
CENTER
MODE
switch to the OFF
position. Play back a monaural source. Then adjust balance so that you
hear minimum volume from all channels.
(See page 31.)
MULTI-ROOM
REMOTE IN jack.
When using the optional MR-100 adaptor for multi-room remote control,
connect to this jack.
REAR AMP jacks
{PRE OUT]
When e separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
{POWER IN]
When a separate pre-amplifier is used for rear speakers and this unit
is used as a power amplifier, connect the pre-amplifier to these jacks.
@
CENTER AMP jacks
[POWER IN} {VSX-3500S only)
When a separate pre-amplifier is used for center speaker and this unit
is used as @ power amplifier, connect the pre-amplifier to this jack.
[PRE-OUT]
When a separate power amplifier is used to drive the center speaker,
connect the power amplifier to this jack.
() CENTER
SPEAKER
terminal (VSX-9500S
only)
Connect the center speaker here.
NOTE.
Use @ center speaker with an impedance fram & ohms to 716 ohms.
@
VIDEO ADAPTOR
jacks
Use to connect a video adaptor Component such as a video enhancer
or color corrector.
@® §S (connector) video jacks
When used in conjunction with a VCR, VDP or monitor TV equipped
with S video jacks, connect to these jacks.
@ VIDEO OUT jacks
Use to connuct a TV set for watching program materials from a VCR
or VDP connected to this unit.
[TO MONITOR TV jack}
Connect to a monitor TV or a TY set with video input terminals,
* If monitor with S-VHS input connector is used, you also need fine
out to video monitor.
{TO RF MODULATOR jack]
Use to connect a conventional TV set. When performing connections,
the
RF
MODULATOR
JA-RF5
(sold
separately)
is required.
By
connecting an RF modulator, video signal can be converted to VHF
signal (U.S. channel 3 or 4), thus allowing this unit to be used to view
the selected source on a Conventional television set.
NOTE
* A "conventional TV set" has an antenna input terminals only.
* Do not allow any of the cord's conductors
to protrude from the
terminals
or
touch
any
other
conductors.
Maffunctioning
or
breakdown may occur when conductors come into contact with each
other.
* Don't connect the TO MONITOR TV VIDEO OUT (RCA pin jack and
S jack) and the TO RF MODULATOR jack to the same set at the same
time.
@
AC OUTLETS
{U.S. and Canadian models]
SWITCHED TOTAL 200 W MAX
[VSX-9500S)
Power
supplied through these outlets is turned on and off by the
receiver's
POWER
switch.
Total electrical power
consumption
of
connected equipment should not exceed 200 W
SWITCHED
TOTAL 300 W MAX
(VSX-7500S)
Power
supplied through these outlets is turned on and off by the
receiver's
POWER
switch.
Total electrical
power
consumption
of
connected equipment should not exceed 300 W.
UNSWIiTCHED 200 W MAX
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 200 W.
[Multi-voltage model]
SWITCHED TOTAL
100 W MAX
Power
supplied through these outlets is turned on and off by the
receiver's
POWER
switch.
Tota! electrical
power
consumption
of
connected equipment shouid not exceed 100 W.
UNSWITCHED
100 W MAX
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed
100 W.
NOTE:
¢ This unit should be disconnected by removing the power plug from
the wall socket when not in regular use, e.g. when on vacation.
* Do not connect appliances with high power consumption such as
heaters, irons, or television sets to these AC OUTLETS in order to
avoid overheating and fire risk.
This can cause the receiver to malfunction.
@
Audio INPUT jacks
PHONO
. Connect to turntable.
. Connect to compact disc player.
waldddebacceveavedae Connect to the audio output jacks of an additional
audio component.
23
<ARB1173>