Pioneer VSX-D309 Manuale di istruzioni per l'uso - Pagina 28
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Ricevitore stereo Pioneer VSX-D309. Pioneer VSX-D309 48. Audio/video multi-channel receiver
Stampa la pagina
Sound Modes
Switching ANALOG/DIGITAL Signal Input
Set this switch to tell the receiver whether you're using a component that is hooked up digitally or in an analog
manner. If you have no components connected digitally the switch wonb't allow you to select digital.
CD-R/
RECEIVER TUNER
TV CONT
TAPE/MD
2
DSP MODE MIDNIGHT 5.1CH
1
2
3
4
CHANNEL
TEST
SIGNAL
SELECT
TONE
ATT
SELECT
5
6
7
8
CHANNEL
EFFECT
LEVEL
‡
9
0
ENTER
10
DISC
CH
FUNC
Each press switches between ANALOG
and DIGITAL signal selection.
SIGNAL
SELECT
ANALOG
When a Dolby Digital
signal is input.
SIGNAL
SELECT
ANALOG
DIGITAL
2DIGITAL
SIGNAL SELECT
Playing a Source
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR
CD-R/
RECEIVER TUNER
TAPE/MD
2
DSP MODE MIDNIGHT 5.1CH
1
2
3
CHANNEL
TEST
SELECT
TONE
ATT
5
6
7
CHANNEL
LEVEL
EFFECT
‡
9
0
10
FUNC
TV CONTROL
VOL
FQ
ST
ENTER
MENU
FQ
SOURCE CLASS
MPX
7
8
D.ACCESS
CHANNEL
1
¡
4
3
LOUDNESS FUNCTION MUTING
FL
REMOTE
RECEIVER
DIMMER
SETUP
2
AUDIO/VIDEO PRE-PROGRAMMED
REMOTECONTROLUNIT
28
1 Press SIGNAL SELECT to select the input
signal corresponding to the source
SIGNAL
component.
SELECT
Each press switches between ANALOG and DIGITAL signal
selection.
2 While SIGNAL SELECT is set to DIGITAL,
DIGITAL lights when a Dolby Digital signal is
input, DTS lights when a DTS signal is input.
SIGNAL
SELECT
ANALOG
DIGITAL
memo
When a DTS
signal is input.
• SIGNAL SELECT is fixed in the "ANALOG" position for components
SIGNAL
not assigned to one of the two digital input jacks.
SELECT
ANALOG
• This receiver can only play back Dolby Digital, PCM (32kHz, 44kHz, and
DIGITAL
48kHz), DTS, digital signal formats. With digital signal formats other
DTS
than these, set SIGNAL SELECT to "ANALOG".
• When an LD or CD player compatible with DTS is played back with
SIGNAL SELECT set in "ANALOG", digital noise is output caused by
playing back the DTS directly (no decoding). To prevent noise, you
need to make digital connections (Refer to page 11) and set SIGNAL
SELECT to "DIGITAL".
• Some DVD players don't output DTS signals. For more details, refer to
the instruction manual supplied with your DVD player.
• Audio from a karaoke microphone and some LDs are analog so set the
SIGNAL SELECT to "ANALOG" in these cases.
• For analog LDs and karaoke microphones, set the switch to
"ANALOG."
1 Turn on the power of the playback
Î
component.
CD
3
TV CONT
2 Turn on the power of the receiver.
4
Be sure that the standby indicator turns off on
4
SIGNAL
SELECT
the front panel.
8
ENTER
3 Press MULTI CONTROL buttons or the
DISC
CH
FUNCTION button to select the source you
VOL
want to playback.
ST
TOP
If the DIRECT FUNCTION is OFF you have to use the FUNCTION
MENU
button to select the source (see p.22).
BAND
3
¢
4 If necessary, press SIGNAL SELECT to select the
input signal corresponding to the source
MASTER
VOLUME
component (as above).
5 Start playback of the component you selected
in step 1.