Pioneer VSX-D3S Istruzioni per l'uso - Pagina 30

Sfoglia online o scarica il pdf Istruzioni per l'uso per Ricevitore stereo Pioneer VSX-D3S. Pioneer VSX-D3S 40. Audio/video stereo receiver
Anche per Pioneer VSX-D3S: Manuale di istruzioni per l'uso (40 pagine)

Stampa la pagina
Pioneer VSX-D3S Istruzioni per l'uso
SOUND EDIT OPERATION (GUI OPERATION)

LEVEL AND BALANCE ADJUSTMENT

÷ First, perform settings in the "SETTING THE SPEAKER MODE".
(Refer to page 29.)
÷ If you press the SOUND EDIT button on a function operation
display, display switches to "SOUND EDIT" indications for the
currently selected surround mode.
(When using PRO-LOGIC THEATER)
S O U N D E D I T
P R O - L O G I C T H E A T E R
SPEAKER
M A S T E R B A L A N C E
MODE
L
R E A R B A L A N C E
L
CENTER LEVEL
REAR LEVEL
SUB WF LEVEL
E F F E C T LEVEL
÷ Adjust level and balance settings with the buttons.
÷ In the "SETTING THE SPEAKER MODE", parameters for
channels set to "NONE" cannot be adjusted.
Switches to the SPEAKER MODE display. (Refer
SPEAKER
to page 29.)
MODE
This switches the test tone signal used for
TEST
adjustment ON/OFF. When ON, the test tone is
TONE
output through each channel in turn. The display
below the TEST TONE button indicates the
channel through which the test tone is being
output.
(Example) F-L : Front Left channel
L R
MASTER BALANCE
÷ Adjust the system's overall left/right volume level balance.
÷ Press
and the right channel's volume level decreases.
L
÷ Press
R
and the left channel's volume level decreases.
L R
REAR BALANCE
÷ Adjust rear channel left/right volume level balance.
÷ Press
and the right rear channel's volume level decreases.
L
÷ Press
R
and the left rear channel's volume level decreases.
– +
CENTER LEVEL
÷ Adjust center channel volume level. ( 10 dB)
÷ Press
–
to lower volume, press
– +
REAR LEVEL
÷ Adjust rear channel volume level. ( 10 dB)
÷ Press
–
to lower volume, press
– +
SUB WF LEVEL
÷ Adjust sub-woofer channel volume level. ( 10 dB)
÷ Press
–
to lower the volume, press
30
<
>
ARB7050
TEST
TONE
F - L
R
R
–
+
+10
dB
–
+
–10
dB
–
+
+6
dB
–
+
50
EXIT
+
to raise volume.
+
to raise volume.
+
to raise volume.
NOTE:
If you adjust the level to match a program source with little bass,
clipping may occur with a program source that has a lot of bass,
resulting in distortion from the sub-woofer. Pay careful attention
to sub-woofer channel output, making sure the level is not too
high.
– +
EFFECT LEVEL
÷ Adjust surround effect level. (10 – 80)
÷ Press
–
to reduce the surround effect, press
EXIT
Press
to return to the original function display.
7 Adjustment using the TEST TONE
1. Press the TEST TONE button to switch ON.
÷ The test tone is output from channels set in the "SETTING
THE SPEAKER MODE".
+
L
R
2. Use the
,
,
, and
volume level balance.
÷ Adjust so that the volume level of each channel is the same.
3. Press the TEST TONE button to switch OFF.
4. Press the EXIT button.
+
to increase it.
–
buttons to adjust channel