Pioneer VSX-D7025 Manuale di istruzioni per l'uso - Pagina 20
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Ricevitore stereo Pioneer VSX-D7025. Pioneer VSX-D7025 44.
Stampa la pagina
FRONT PANEL FACILITIES
@) DOLBY 3CH LOGIC button
Select this setting when stereo-source regeneration and rear speak-
ers are not connected and you wish to use the front L, front R,
and
center
speakers
to enjoy audio/visual
material
bearing
the
DIC [pow sunnouND] mark
MASTER VOLUME control
Use it to simultaneously adjust the sound volume from the front, center
and rear speakers.
PHONES jack
Connect the plug on your headphones to this jack. Set all SPEAKERS
A and B switches to OFF if you want to cut the sound from speakers
and listen to it only through the headphones.
@ SPEAKERS buttons (A, B) & OFF = ON
ON/OFF switches for the A and B speaker systems.
NOTE:
:
No sound will be heard thorough the speakers when both A and B
buttons are depressed if only one set of speakers has been connected
to either A or B SPEAKERS terminals.
@) BAND (FM/AM) button
Use this to switch between FM and AM frequency band reception.
@ TUNING buttons
+: Performs tuning from the currently displayed station frequency in
ascending frequency order.
- : Performs tuning in order of descending frequencies.
@ INPUT SELECTOR buttons
VCR 1:
Press when performing playback on a first VCR unit.
VCR 2:
Press when performing playback on a second VCR unit.
LD:
Press when performing playback on an LD player.
TV:
Press when using a TV tuner connected to the TV jacks.
VIDEO:
Press when performing playback on a VCR connected to
VIDEO INPUT jacks on the front panel.
TAPE 1/DAT:
Press when performing playback on a DAT or cassette deck.
:
TAPE 2 MONITOR:
Press when performing playback on a second cassette deck
or second DAT and when monitoring recording.
CD:
Press when playing compact discs on a CD player.
TUNER:
Press when listening to radio broadcasts.
PHONO:
Press when playing records on turntable.
20
<ARB1421>
@) ACOUSTIC buttons (See page 28)
MEMORY:
:
Pressing this button will result in the memorization of the sound quality
{tone control condition). Press again to cancel this mode.
SELECT:
¢ This button is used to preset the five acoustic memories (A—E).
* This button is also used to recall previously set sound quality settings.
Each time you press the. button, the sound quality setting advances
in the order shown below.
peers
ee
er
ee
oe
FLAT:
For flat (normal) frequency response.
LOUDNESS:
Emphasizes
the low- and high- frequency
ranges.
Produces a fuller sense of sound, particularly when
listening at low volume.
:
A-E:
Memorized acoustic memory settings.
@ RESET button
Use this when normal operation becomes impossible because of external
influences such as static electricity or lightning, or when operation is
impossible even when operation buttons are pressed. Press this button
to return to normal operating conditions.
if you press this button when the power is ON, the unit switches to
POWER STANDBY, and the entire Contents of the memory are erased.
@) RETURN button
Press this button to return the receiver into the initial state. TUNER is
selected at this initial state. Adjust the sound level by using the MASTER
VOLUME control.
© TAPE 2 MONITOR ....... OFF
e FUNCTION.............. TUNER
e SURROUND MODE....... OFF
=e V-SIGNAL SELECTOR.... OFF
© MUTING ..... ee eeeeeees OFF
= ® TONE... .ccccesecseerenevevens flat
¢ BALANCE ............. CENTER
The
HITS
function
searches
for broadcast
stations
among
the
frequencies displayed.
NOTE:
If no sound is output after the RETURN button is pressed, make sure
that SPEAKERS buttons are turned on.
@ MUTING button
Press to temporarily cut off the sound volume. When pressed again,
the sound will return to its previous level.
VIDEO INPUT jacks
VIDEO
components
such as a VCR
or TV camera,
etc. can be
connected.