Pioneer A-300R Manuale di istruzioni per l'uso - Pagina 11

Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Amplificatore Pioneer A-300R. Pioneer A-300R 13.

Stampa la pagina

SPECIFICATIONS

Amplifier Section

Continuous power ouiput

{both channels driven at 20 Hz to 20 kHz}*

T.H.D. 0.07 %, 82

35W+35W

T.H.D.0.1%,4Q..

40 W +40 W

DIN Continuous power output (both channels driven at 1 kHz}

DE 130-96,

B90).22t. cs coast

hip dra

ered 45W+45W

T.H.D.10%,42

55 W+55W

Dynamic power output (E.L.A. test signal)

Total harmonic distortion*

20 Hz to 20 KHZ, 17.5 W, 8 Q onc cceeceeseeeeteeeeeeenes 0.05 %

Input sensitivity/ impedance

PHONO (MIM) vicssseseorecescostiatasevacsstvvieresensivananee 2.8 mV/ 50 kQ

CD, TUNER, LINE, TAPE 1/DAT, TAPE

2 MONITOR

Wes ngitate sabe Sdtehvodesetaedaeieecese catatesebuasudstesh debeiusedeous 200 mV/ 50 kQ

PHONO overload level

VG A2 0D

O51 8G (MM) aati

tra ca deattiedetal teat 150 mV

Output level/ impedance

TAPE 1/DAT, TAPE 2 MONITOR o....cccccceeeeees 200 mV/ 1 kQ

Frequency response

PHONO (MM)... ceseeestesessceneeteeeenees 20 Hz to 20 kHz

+ 0.5 dB

CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR

.5 Hz to 100kHz °3dB

Signal -to-Noise ratio (IHF short circuit, A network}

PHONO (MM, 5 mV input) ..

CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR...

Signal-to-Noise ratio (DIN, continuous power/ 50 mW)

PHONO (MM)

. 70 dB/ 64 6B

CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR

88 dB/ 67 dB

82dB

107 dB

Power Supply/ Miscellaneous

Power requirements

UL Kod ell: ...5ctsieuveraiiec

odin AC 230 Volts, 50/60 Hz

Round 2-pin AC plug mode'!

AC 220 ~ 230 Volts, 50/60 Hz

Australia model ..

AC 240 Volts, 50/60Hz

Multi-voitage model .

AC 110 V/129~127 V/220 V/240 V

(switchable), 50/60HZ

Power CONSUMPTION os ceeecesseccereseereseseseetcese

. 8330 W

Dimensions {including knobs and other prstdding parts)

- 420 (W) & 310 1D) & 110 (H) mm

Accessories

Remote control unit

Batteries (AA/REP) ...

Operating instructions

Power cord ....

mi ana

NOTE:

Specifications and design subject to possible modification without

Notice, due to improvements.

* Measured by Audio Spectrum Analyzer.

MAINTENANCE OF EXTERNAL SURFACES

* Use a polishing cloth or dry cloth to wipe off dust and dirt.

* When the surfaces are very dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water, and

wrung out well, and then wipe again with a dry cloth. Do not use

furniture wax or cleaners.

Never use thinners, benzine, insecticide sprays and other chemi-

cals on or near this unit, since these will corrode the surfaces.