Pioneer GM-6000F Manuale d'uso - Pagina 3
Sfoglia online o scarica il pdf Manuale d'uso per Amplificatore Pioneer GM-6000F. Pioneer GM-6000F 9. Bridgeable four-channel power amplifier
Anche per Pioneer GM-6000F: Manuale d'uso (6 pagine)
Stampa la pagina
Connecting the Unit
Connecting the Power Terminal
4. Connect the wires to the terminal.
• Fix the wires securely with the terminal
• Always use the special red battery and ground
screws.
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
GND terminal
terminal (+) and the ground wire to the car body.
Power terminal
System remote
control terminal
1. Pass the battery wire from the
engine compartment to the interior
System remote
of the vehicle.
control wire
• After making all other connections to the
amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.
Engine
Fuse (30 A)
compart-
Interior of
ment
the vehicle
Battery wire
Fuse (30 A)
Drill a 14 mm
Positive terminal
(1/2 inch) hole
Insert the O-ring rubber
into the vehicle
grommet into the vehicle
body.
body.
2. Twist the battery wire, ground wire
and system remote control wire.
Twist
3. Attach lugs to wire ends. Lugs not
supplied.
• Use pliers, etc., to crimp lugs to wires.
Lug
Ground wire
Lug
Battery wire
Connecting the Speaker Output
3. Connect the speaker wires to the
speaker output terminals.
Terminals
• Fix the speaker wires securely with the termi-
nal screws.
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm (3/8 inch) and twist.
Twist
10 mm
Ground wire
(3/8 inch)
Speaker output
2. Attach lugs to speaker wire ends.
terminal
Lugs not supplied.
• Use pliers, etc., to crimp lugs to wires.
Lug
Speaker wire
Connecting the Speakers and Input wires
The speaker output mode can be four-channel, three-channel (stereo +
mono) or two-channel (stereo, mono). Connect the speaker leads to suit the
mode according to the figures shown below.
Four-channel mode
Terminal screw
Input Select Switch
For two-channel input, slide this switch to
the left. For four-channel input, slide this
switch to the right.
RCA input jack B
RCA input jack A
Speaker wire
Connecting wires
with RCA plugs (sold
separately)
From car stereo (RCA output)
If only one input plug is used, such as when
the car stereo has only one output (RCA out-
put), connect the plug to RCA input jack A,
but do not connect a plug to RCA input jack B.
Three-channel mode
Input Select Switch
For two-channel input, slide this switch to
the left. For four-channel input, slide this
RCA input jack B
switch to the right.
RCA input jack A
Connecting wires
with RCA plugs (sold
separately)
From car stereo (RCA output)
If only one input plug is used, such as when
the car stereo has only one output (RCA out-
put), connect the plug to RCA input jack A,
but do not connect a plug to RCA input jack B.
Two-channel mode (stereo)
RCA input jack A
Input Select Switch
Slide this switch to the left.
(Left)
Connecting wire with RCA
Speaker out A
plugs (sold separately)
(Right)
From car stereo (RCA output)
+
≠
≠
+
Two-channel mode (mono)
+
≠
≠
+
(Right)
Speaker out B
RCA input jack A
Input Select Switch
(Left)
Slide this switch to the left.
Connecting wire with RCA
plugs (sold separately)
(Left)
Speaker out A
From car stereo (RCA output)
(Right)
+
≠
≠
+
≠
+
Speaker out B
(Mono)
Speaker (Left)
+
≠
≠
+
Speaker (Right)
Speaker (Mono)
+
≠
≠
+
Speaker (Mono)