Pioneer GM-D8701 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Amplificatore Pioneer GM-D8701. Pioneer GM-D8701 8. Class d mono amplifier
Anche per Pioneer GM-D8701: Manuale d'uso (16 pagine), Manuale d'uso (16 pagine)

Stampa la pagina

1. Installation

Connecting the units

Connections when using

Solderless terminal

the speaker input wire

connections

Connect the car stereo speaker output wires

! Since the wire will become loose over time,

to the amplifier using the supplied speaker

it must be periodically inspected and tigh-

input wire with RCA pin cord.

tened as necessary.

! Do not solder or bind the ends of the

twisted wires.

! Fasten while making sure to not to clamp

the insulating sheath of the wire.

! Use the supplied hexagonal wrench to

tighten and loosen the terminal screw of

the amplifier and use it to securely fasten

the wire. Be careful to avoid excessive tigh-

tening of this screw, which may damage

1 Car Stereo

the wire.

2 Speaker output

3 Red: Right +

Connecting the power terminal

4 Black: Right *

5 Black: Left *

WARNING

6 White: Left +

If the battery wire is not securely fixed to the term-

7 Speaker input wire with RCA pin cord

inal using the terminal screws, there is a risk of

To the RCA input jack of this unit

overheating, malfunction and injury, including

minor burns.

Notes

! If speaker input wires from a headunit are

! Always use the recommended battery and

connected to this amplifier, the amplifier will

ground wire, which is sold separately. Con-

automatically turn on when the headunit is

nect the battery wire directly to the car bat-

turned on. When the headunit is turned off,

tery positive (+) terminal and the ground

the amplifier turns off automatically. This

wire to the car body.

function may not work with some headunits.

! Recommended wires size (AWG: American

In such cases, please use a system remote

Wire Gauge) is as follows. The battery wire,

control wire (sold separately). If multiple am-

the ground wire and the optional direct

plifiers are to be connected together synchro-

ground wire must be same size.

nously, connect the head unit and all

! Use a wire of 8 AWG to 16 AWG wire for the

amplifiers via the system remote control wire.

speaker wire.

! Connect the system remote control wire when

you wish to only turn on the car stereo, not the

Battery wire and ground wire size

amplifier.

! This amplifier automatically selects an input

Wire length

Wire size

signal mode between the RCA level and the

less than 3.6 m

6 AWG

speaker level by detecting an input signal.

less than 6.4 m

4 AWG

Connecting the units

Route battery wire from engine com-

partment to the vehicle interior.

! When drilling a cable pass-hole into the ve-

hicle body and routing a battery wire thor-

ough it, take care not to short-circuit the

wire damaging it by the cut edges or burrs

of the hole.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive + battery term-

1 Battery wire

inal.

2 Power terminal

3 Ground wire

4 GND terminal

5 System remote control wire

6 System remote control terminal

7 Terminal screws

1 Positive + terminal

2 Battery wire (sold separately)

The maximum length of the wire between

the fuse and the positive + terminal of the

battery is 30 cm.

3 Fuse 100 A (GM-D8701) / 150 A (GM-D9701)

(sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701) / 150 A (GM-D9701).

Use wire cutters or a utility knife to

strip the end of the battery wire, ground

wire and system remote control wire to ex-

pose about 10 mm of the end of each of

the wires, and then twist the exposed ends

of the wires.

Twist

10 mm

Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

Connecting the units

Installation

Connecting the speaker output

Before installing the amplifier

terminals

Use wire cutters or a utility knife to

! To ensure proper installation, use the supplied

strip the end of the speaker wires to ex-

parts in the manner specified. If any parts

pose about 10 mm of wire and then twist

other than those supplied are used, they may

the wire.

damage internal parts of the amplifier, or be-

Twist

come loose causing the amplifier to shut

down.

! Do not install in:

— Places where it could injure the driver or

10 mm

— Places where it may interfere with the dri-

Connect the speaker wires to the

speaker output terminals.

! Install tapping screws in such a way that the

Fix the wires securely with the terminal

screw tip does not touch any wire. This is im-

screws.

portant to prevent wires from being cut by vi-

bration of the car, which can result in fire.

! Make sure that wires do not get caught in the

sliding mechanism of the seats or touch the

legs of a person in the vehicle as short-circuit

may result.

! When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment

1 Terminal screws

(e.g. fuel/brake lines, wiring) from damage.

2 Speaker wires

3 Speaker output terminals

! To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

— Allow adequate space above the amplifier

— Do not cover the amplifier with a floor mat

! Place all cables away from hot places, such

as near the heater outlet.

! The optimal installation location differs de-

pending on the car model. Secure the ampli-

fier at a sufficiently rigid location.

! Check all connections and systems before

final installation.

! After installing the amplifier, confirm that the

spare tire, jack and tools can be easily re-

moved.

Installation

Attaching the Bass boost

remote control

WARNING

Attach with tapping screws (3 mm × 10 mm)

at an easily accessible location such as under

the dashboard.

passengers if the vehicle stops suddenly.

ver, such as on the floor in front of the dri-

ver's seat.

Tapping screws (3 mm × 10 mm)

Example of installation on

the floor mat or chassis

Place the amplifier in the desired instal-

lation location.

Insert the supplied tapping screws (4 mm ×

18 mm) into the screw holes and push on the

screws with a screwdriver so they make an im-

print where the installation holes are to be lo-

cated.

Drill 2.5 mm diameter holes at the im-

CAUTION

prints either on the carpet or directly on

the chassis.

for proper ventilation.

or carpet.

Install the amplifier with the use of

supplied tapping screws (4 mm × 18 mm).

1 Tapping-screws (4 mm × 18 mm)

2 Drill a 2.5 mm diameter hole

3 Floor mat or chassis

4 Hole-to-hole distance: 229.5 mm (GM-

D8701) / 279.5 mm (GM-D9701)

5 Hole-to-hole distance: 191.5 mm