Pioneer Premier PRS-D2000T Manuale d'uso - Pagina 2

Sfoglia online o scarica il pdf Manuale d'uso per Amplificatore Pioneer Premier PRS-D2000T. Pioneer Premier PRS-D2000T 6. Bridgeable two-channel power amplifier
Anche per Pioneer Premier PRS-D2000T: Manuale d'uso (9 pagine)

Stampa la pagina

Connecting the Unit

CAUTION

• Disconnect the negative (–) terminal of the battery

• Make sure that wires will not interfere with mov-

to avoid the risk of short-circuit and damage to

ing parts of the vehicle, such as the gearshift,

the unit.

handbrake or seat sliding mechanism.

• Secure the wiring with cable clamps or adhesive

• Do not shorten any wires. Otherwise the protec-

tape. To protect the wiring, wrap adhesive tape

tion circuit may fail to work when it should.

around it where they lie against metal parts.

• Never feed power to other equipment by cutting

• Do not route wires where they will get hot, for

the insulation of the power supply wire to tap

example where the heater will blow over them. If

from the wire. The current capacity of the wire

the insulation heats up, it may become damaged,

will be exceeded, causing overheating.

resulting in a short-circuit through the vehicle

• Never replace the fuse with one of greater value

body.

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

• Speakers to be connected to the amplifier should

nect a negative (–) lead wire for several speakers.

conform with the standards listed below. If they

• This unit is for vehicles with a 12-volt battery and

do not conform, they may catch fire, emit smoke

negative grounding. Before installing it in a recre-

or become damaged. The speaker impedance must

ational vehicle, truck or bus, check the battery

be 2 to 8 ohms for stereo connection, and 4 to 8

voltage.

ohms for monaural and other bridge connection.

• If the car stereo is kept on for a long time while

• Install and route the separately sold battery wire

the engine is at rest or idling, the battery may go

as far away as possible from the speaker wires.

dead. Turn the car stereo off when the engine is at

Install and route the separately sold battery wire,

rest or idling.

ground wire, speaker wires and the amplifier as

• If the system remote control wire of the amplifier

far away as possible from the antenna, antenna

is connected to the power terminal through the

cable and tuner.

ignition switch (12 V DC), the amplifier will

• Cords for this product and those for other prod-

always be on when the ignition is on— regardless

ucts may be different colors even if they have the

of whether the car stereo is on or off. Because of

same function. When connecting this product to

this, the battery could go dead if the engine is at

another product, refer to the supplied Installation

rest or idling.

manuals of both products and connect cords that

have the same function.

Speaker Channel

Speaker Type

Power

Subwoofer

Nominal input: Min. 150 W

Two-channel

Other than subwoofer

Max. input: Min. 300 W

Subwoofer

Nominal input: Min. 600 W

One-channel

Other than subwoofer

Max. input: Min. 1 200 W

Connection Diagram

• This diagram shows connections using external output (subwoofer output). Slide the input switch to the left.

• When you connect with speaker output, connections defers from the diagram. For details, see the "Using the

Speaker Input" section. In either case, you need to set the input switch. For details, see the "Setting the Unit"

section.

Fuse (30 A)

Special red battery wire [RD-223] (sold separately)

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Grommet

Fuse (30 A)

Ground wire (black) [RD-223] (sold separately)

Connect to metal body or chassis.

External Output

Bass Boost

Car stereo with

Remote Control

Bass Boost Remote

RCA output jacks

Control Wire

6 m

Jack for the bass boost remote control

Connect this jack and the bass boost

Connecting wire with RCA

remote control with the bass boost

pin plugs (sold separately).

remote control wire.

RCA input jack

RCA output jack

Fuse (30 A)

Speaker output terminal

Amplifier with

See the "Connecting

RCA input jacks

the Speaker Wires"

RCA input

section for speaker

connection instructions.

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car stereo (SYSTEM

REMOTE CONTROL). The female terminal can be connected to the auto-antenna relay control

terminal. If the car stereo does not have a system remote control terminal, connect the male terminal to

the power terminal through the ignition switch.

Connecting the Power Terminal

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

• Always use the special red battery and ground

screws.

wire [RD-223], which is sold separately. Connect

GND terminal

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

Power terminal

System remote

control terminal

1. Pass the battery wire from the

engine compartment to the interior

System remote

of the vehicle.

control wire

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

Engine

Fuse (30 A)

compart-

Interior of

ment

the vehicle

Battery wire

WARNING

Fuse (30 A)

Drill a 14 mm

Failure to securely fasten the battery wire to the ter-

Positive terminal

hole into the

minal using the terminal screws could cause the ter-

vehicle body.

Insert the O-ring rubber

minal area to overheat and could result in damage

grommet into the vehicle

and injury including minor burns.

body.

2. Twist the battery wire, ground wire

and system remote control wire.

Twist

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Ground wire

Lug

Battery wire

Connecting the Speaker Output

Using the Speaker Input

Terminals

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input wire with RCA pin cord.

1. Expose the end of the speaker wires

• Slide the input switch to the right.

using nippers or a cutter by about

7 Connections when using the speaker

10 mm and twist.

input

Twist

10 mm

Ground wire

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Speaker wire

White:

3. Connect the speaker wires to the

Left + Left ≠

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Terminal screw

To RCA

Speaker

input jack of

output

this unit.

terminal

• As a result of connecting the car stereo speaker

Speaker wire

output wire to the amplifier, the power of the

amplifier is turned on automatically when the car

stereo is turned on. It is not necessary to connect

the system remote control wire in this case.

Note:

• Connect the system remote control wire when the

power of the amplifier is not to be turned on when

the car stereo is turned on.

Car Stereo

Speaker

output

Black:

Red:

Right ≠ Right +

Speaker input

wire with RCA

pin cord