Ariston AW122 Libretto di cura, uso e installazione - Pagina 13

Sfoglia online o scarica il pdf Libretto di cura, uso e installazione per Lavatrice Ariston AW122. Ariston AW122 20. Washer / washer-dryer combo
Anche per Ariston AW122: Libretto di cura, uso e installazione (20 pagine), Manuale di riparazione (20 pagine), Manuale rapido (21 pagine)

Ariston AW122 Libretto di cura, uso e installazione

Installation Requirements

Tools and Parts

Assemble the necessary tools and supplies before
beginning the washer installation. The parts supplied
are in the drum.
Tools needed for installation:
10mm Wrench, Screwdriver
Parts Supplied
U-Clamp
If You Have
You'll Need to Buy
No access to Hot/Cold
Splendide Faucet Adapter kit,
Part No.154187104A (8ft , 2.4m)
water hookups
Splendide Drain-A-Way™ Pan,
Water damage
Concerns
Part No. PI-22, PI-24 (or similar)
Floor drain
Siphon break kit (sold at most
hardware stores)
Disposer drain
"Y" connector (sold at most
hardware stores)
Shifting Concerns
Splendide SecureFit™
(RV and Marine
installation Brackets, Part No.
Installations)
MK01. Keeps washer in place dur-
ing travel to prevent:
Kinked inlet hoses
Disconnected dryer vent
hoses
Crushed dryer vent hose
Blocked dispenser drawer
Knobs rubbing against closed
doors
Scuffed cabinet woodwork
All Splendide parts are available
direct from Westland Sales: 1-800-356-0766
Transit Bolt Hole Plugs (4)

Location

Selecting the proper location for the washer-dryer
improves performance and minimizes noise. Proper
installation is your responsibility. The washer-dryer
can be installed under a counter, in a closet, in an
alcove, or in a recessed area with minimum installation
clearances of 0" sides, 1" front/back.
You'll Need
• A water heater set to deliver 120°F (49°C) water to
the washer.
• A grounded electrical outlet located within 6 ft.
(1.8m) of where the power cord is attached to the
back of the washer. (See "Electrical Requirements.")
Make sure the electrical socket is accessible so you
can unplug the washer when not in use.
• Hot and cold water faucets located within 8ft. (2.4
m) of the hot and cold water fill valves, and water
pressure of 7.5-100 psi.
• A solid, level floor that can support at least 280
lbs. (127 kg). DO NOT install on carpet. The ma-
chine must rest solid on a sturdy floor for optimum
performance and minimum vibration.
• Enough space to open the door fully so you can load
and unload easily.
• RV/Marine Installations: When locating the appli-
ance in a towable trailer or watercraft, position the
machine over the axles or mid-ship where move-
ment is at a minimum. Block the machine to prevent
extreme movement or tipping.

Water Inlet Requirements

Water pressure must range within 7.5 and 100 psi. If
the water pipes are new or left unused, before con-
necting the machine, run the water until clear to
remove debris. Connect the inlet hose to a cold water
tap having a 3/4" BSP thread. Ensure that there are
rubber washers at the end of each inlet hose. The
L-Shaped end goes on the machine and the straight
ends on the water faucets.
CAUTION!
1.
This washing machine must only be
operated with cold and hot tap water. Do
not connect the appliance to a mixer tap of
an unpressured hot-water boiler.
2.
To prevent water damage, the hot and cold
water valves should be accessible when
the washer is in place and should always be
turned off when the washer is not in use.
13