Ariston LFF 825 Manuale di istruzioni per l'uso - Pagina 9
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Lavastoviglie Ariston LFF 825. Ariston LFF 825 36.
Anche per Ariston LFF 825: Manuale di istruzioni per l'uso (16 pagine)
Rinse aid and refined salt
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard
or very hard. Follow the instructions given on the
packaging.
*
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
*
When the LOW RINSE AID
indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the lid
(G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure it
does not overflow from the dispenser. If
this happens, clean the spill immediately
F
with a dry cloth.
3. Screw the lid back on.
G
NEVER pour the rinse aid directly
into the appliance tub.
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Switch on the appliance by pressing the ON/OFF button.
- Press the P button and hold for a few seconds; two short
beeps will sound and the wash cycle indicator light
corresponding to the set degree of hardness will flash slowly
on the control panel (the water softening system is set to
number 3).
- Press the P button repeatedly until the desired hardness
level has been reached (1-2-3-4-5
table).
*
see Water hardness
E.g. Hardness level 1 (1
wash cycle indicator light flashes)
st
Hardness level 2 (1
st
wash cycle indicator light on, 2
cycle indicator light flashes)
Hardness level 3 (1
and 2
wash cycle indicator lights on, 3
st
nd
wash cycle indicator light flashes etc.) up to a maximum of
level 5*.
- To exit the function, wait approximately 30 seconds or switch
off the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
°dH
°fH
0
6
0
10
6
11
11
20 1.1
12
17
21
30 2.1
17
34
31
60 3.1
34
50
61
90 6.1
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
When the green float* cannot be seen by simply looking at
the cap of the salt dispenser.
When the LOW SALT* indicator light on the control panel is
illuminated;
1. Remove the lower rack and
unscrew the container cap
(anticlockwise).
2. The first time you do this: fill the
water tank right up to its edge.
3. Position the funnel
fill the salt container right up to its
edge (this should hold approximately
1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel* and wipe any salt residue away from
the opening; rinse the cap under running water and then
screw it on, the head facing downwards so as to let the
water flow out of the four cracks which are arranged in a
star shape on the lower part of the cap. (the container cap
*
with the green float
)
It is advisable to perform this procedure every time you
add salt to the container.
Make sure the cap is screwed on tightly, so that no
detergent can get into the container during the wash cycle
(this could damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
*
Only available in selected models.
nd
wash
rd
mmol/l
level
0
1
1
2
2
3
3
6
4
9
*
5
*
(see figure) and
9
EN