Ariston CX67SP6 X NG Manuale di istruzioni per l'uso, la cura e l'installazione - Pagina 4
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso, la cura e l'installazione per Forno Ariston CX67SP6 X NG. Ariston CX67SP6 X NG 12. Cooker & oven
Anche per Ariston CX67SP6 X NG: Manuale di istruzioni per l'uso (16 pagine), Manuale di istruzioni per l'uso (16 pagine)
Stampa la pagina
Installation
Electrical Connection
The electrical supply for the cooktop must be 240 Volt 50
Hz.
The fuse and electrical wiring of the home/premises must
support the load of the appliance.
The appliance must be earthed.
(New Zealand statutory warning): The cooker must be
connected to the electricity supply by a cable fi tted with an
appropriately rated plug that is compatible with the socket-
outlet fi tted to the fi nal subcircuit in the fi xed wiring that is
intended to supply this cooker.
The appliance must be connected to the mains by means
of an omnipolar switch with a minimum contact opening of
3 mm.
IMPORTANT If a power socket needs to be installed or
relocated, the work must be done by a licensed electrician.
Mounting A Power Supply Cable
Open the terminal board by inserting a screwdriver into the
side tabs of the cover. Use the screwdriver as a lever to open
the cover (see diagram).
Loosen the cable clamp screw and remove it. (see fi gure).
Remove the wire contact screws L-N- , then fasten the wires
under the screw heads, respecting the colour code: Black/
Blue (N), Red/Brown (L) and Bare Wire/Yellow-Green ().
Once the connections have been made, tighten all the termi-
nal screws fully.
Fasten the supply cable in place with the clamp and close
the cover of the terminal board.
The supply cable should be positioned so that it is not sub-
ject to direct heat and so that it does not reach a temperature
of more than 50°C higher than room temperature, along its
length. If there is a risk that the cable will come into contact
with parts having such a temperature rise, then fi xed wiring
insulation must be protected using an insulating sleeve of an
appropriate temperature rating.
Before making the connection, check that the home electrical
system can support the appliance load (see data plate).
NB: Never use reducers, adaptors or shunts since they can
cause heating or burning.
the socket or omnipoar circuit-breaker must be easily acces-
sible once the cooker has been installed. The power cable
must not be bent or compressed.
4
Gas Connection
This appliance is suitable for use with either a fl exible con-
nection or rigid copper connection.
Check The Gas Type
WARNING: Before installation, check that the gas type (natu-
ral gas or LPG/Propane) of the cooker is suitable for the gas
type available to the installation. It is extremely dangerous to
use the wrong gas type with any appliance, as fi re or serious
injury can result.
This cooker is supplied from the factory already set for Natu-
ral Gas. To convert the cooker to LPG (or back to Natural
Gas from LPG), follow the directions later in this section.
Flexible Hose
If a fl exible hose is used, it should be as short as possible
with a maximum length of 1.5 metres;
N
L
Duplicate Data Plate
Where the data plate is obscured by cabinetry when the
cooker is in the installed position, place a duplicate data plate
on a surface of the cabinetry adjacent to the cooker.
Fit regulator supplied for Natural Gas (if applicable) at rear
of appliance, and as close as practicable to the appliance.
It is recommended that an isolating valve and union be
fi tted, to enable simple disconnection for servicing. These
are to be in an accessible location.
The fl exible connection must be approved to class B or D
of AS/NZS1869 as a minimum.
it should not be bent, kinked or compressed;
it should not be in contact with the rear wall of the appli-
ance or in any case with parts which may reach a tem-
perature of 50°C;
it should not come into contact with pointed parts or sharp
corners;
it should not be subject to any pulling or twisting forces;
it should be easy to inspect along its entire length in order
to be able to check its condition.
The supply connection point must be accessible with the
appliance installed.
The inner diameters of the pipe are as follows:
8 mm for LPG;
13 mm for Natural Gas.
The manufacturer declines any liability should these
instructions and safety directions not be observed.