Whirlpool AWO/C 6304 Manuale - Pagina 3
Sfoglia online o scarica il pdf Manuale per Lavatrice Whirlpool AWO/C 6304. Whirlpool AWO/C 6304 15.
Stampa la pagina
•
The symbol
on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment. Disposal
must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household waste
disposal service or the shop where you purchased
the product.
4. Frost
•
Do not place the washing machine in a room
prone to frost. If you must, make sure that the
washingmachine is completely drained after each
wash:
BEFORE USING THE WASHING MACHINE
1. Removing the packaging and
inspection
•
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
•
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
•
If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
2. Remove the transport bolts
•
The washing machine is fitted with transport
bolts to avoid any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
•
After their removal, cover the openings with the 4
enclosed plastic caps.
3. Install the washing machine
•
Remove the protective film from the control panel
(if available on your model).
•
Move the appliance without lifting it by the worktop.
•
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
•
Make sure that all four feet are stable and resting
on the floor and then check that the washing
machine is perfectly level (use a spirit level).
•
In case of wooden or so-called "floating floors" (for
instance certain parquet or laminate floors), place
the appliance on a sheet of plywood at least 60 x
60 cm wide/deep and at least 3 cm thick which is
secured to the floor.
•
Make sure that the ventilation openings in the
base of your washing machine (if available on your
model) are not obstructed by a carpet or other
material.
4. Water inlet
•
Connect the water inlet hose(s) to the drinking
water supply in accordance with the regulations of
your local water company.
•
For models with one inlet valve: cold water
•
For models with two inlet valves: cold AND hot
•
Remove inlet hose(s) from water tap and let the
water flow out completely.
•
Remove drain hose from siphon or handwash
basin and let the water flow out completely.
•
Empty residual water inside the machine by
following the instructions in the chapter "Draining
Residual Water"; for freestanding models: tilt the
appliance forward with two persons to let the rest
water flow out completely.
5. EC Declaration of Conformity
•
The appliance conforms to the following European
Standards: 2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility
Directive.
The Manufacturer is not liable for any damage to
laundry resulting from inadequate or incorrect fabric
care instructions which have been provided with the
garment or article.
water, or cold water only (see chapter "Installation
Guide").
•
Water tap: 3/4" threaded hose connector
•
Water pressure (flow pressure): 100-1000 kPa
(1-10 bar).
•
Use only new hoses to connect the washing
machine to the water supply. Used hoses must not
be used and should be discarded.
•
For models with hot fill: the hot water inlet
temperature must not exceed 60°C.
5. Drain
•
Firmly connect the drain hose to the siphon, or
another outlet for drain water.
•
If the washing machine is connected to an
integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous load-
ing and draining of water (siphoning effect).
6. Electrical connection
•
Electrical connections must be carried out by a
qualified technician in compliance with the manu-
facturer's instructions and current standard safety
regulations.
•
Data regarding voltage, power consumption
andprotection requirements is given on the inside
of the door.
•
The appliance must be connected to the mains
by means of a socket with an earth connection in
accordance with current regulations. The washing
machine must be earthed by law. The manufac-
turer declines all liability for damage to property
or injury to persons or animals due to non-compli-
ance with the directions given above.
•
Do not use extension leads or multiple sockets.
•
Access to the mains plug or disconnection from
the mains supply via a double-pole switch must be
ensured at all times after the installation.
•
Do not operate the washing machine if it has been
damaged during transport. Inform the After-Sales
Service.
•
Mains cable replacement is only to be carried out
by After-Sales Service.
•
When using a residual current circuit breaker
(RCCB), only use a model marked with
GB 2
.