Whirlpool AWO/D 9614 Manuale di istruzioni per l'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Lavatrice Whirlpool AWO/D 9614. Whirlpool AWO/D 9614 18.

Whirlpool AWO/D 9614 Manuale di istruzioni per l'uso
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton / Antibacterial
95
Cotton
60
Cotton with "Eco"***
60
Cotton
40
Synthetics
60
Synthetics
40
Daily load
40
Quick wash
30
Delicates
30
Wool
40
Handwash
40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives"
in your Instructions for Use.
1. Push the "On/Off" button
. The blue light
circle signals that the washer is switched on.
2. Select the desired programme by pushing the
corresponding programme button; it is marked
by a blue light.
3. The temperature and spin speed indicated on
the display can be altered by pressing the
"Temperature" button
or the "Variable
spin" button
.
SELECT ANY DESIRED OPTION
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
"Eco" button
• With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption is
achieved.
"Easy ironing" button
• Can be used together with "Cotton",
"Synthetics" and "Daily load" programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
Load
Water
Energy
Approx. Programme Duration
(kg)
(l)
(kWh)
(hours : minutes)*
6.0
59**
1.90
2:00
6.0
56
1.14
2:10
6.0
51
1.02
2:20
5.0
56
0.70
2:00
2.5
50**
0.80
1:35
2.5
46
0.50
1:20
3.0
41
0.50
1:00
3.0
41
0.40
0:30
1.5
60
0.50
0:45
1.0
60
0.50
0:45
1.0
45
0.50
0:40
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option.
"Intensive rinse" button
• More water is added and rinse cycle is
prolonged.
• This option is particularly suitable for areas with
very soft water or for washing baby linen, and
helps people with allergies.
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics", "Daily load" and
"Delicates".
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• If you select "Rinse hold", do not leave the
laundry to soak for too long.
Note: The programme stops to "Rinse hold" at
the time the "Rinse hold" symbol
display lights up. The blue light under the
"Start/Pause" button
flashes.
Terminate the "Rinse hold" option
• Press the "Start/Pause" button
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, push
"Drain/Reset"
and then start the Drain
programme by pushing the "Start/Pause"
button
.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
SAVE YOUR FAVOURITE PROGRAMMES
If there is a programme setting which you use
frequently, the appliance offers the possibility to
save one setting for each programme so that it can
be used again by just pushing one button.
• Select the desired programme, temperature,
spin speed and option(s), push and hold the
"Favourites" button
The lamp next to "Favourites" shortly flashes
and then lights up - the programme setting is
saved.
Next time you want to use your individual
programme setting, select the programme, push the
"Favourites" button
and start by pushing
"Start/Pause".
If you want to replace the saved programme
setting by another one:
• Push the programme button, select temperature,
spin speed and options as desired and then press
and hold the "Favourites" button
3 seconds. The previously saved programme
setting will be replaced by the new one.
START DELAY
The "Start Delay"
allows to run the machine at
the consumer's convenience, for example at night
when electricity is cheaper.
• Select programme, temperature, spin speed and
options.
• Press the "Start Delay" button to select a delay
time of 1, 3, 6, 9 or 12 hours.
• Press the "Start/Pause" button
The countdown of the delay time begins; the
clock symbol on the display and the delay time
selected flash.
• The delay time and the clock symbol disappear
when the programme starts.
• The number of hours preselected can be reduced
by pressing again the "Start Delay" button.
To cancel the "Start Delay"
on the
• Select another programme or press the
"Drain/Reset" button
PROGRAMME START
:
; the
Open the tap and press the "Start/Pause"
button
. The blue light under the "Start/
Pause" button
is on. The programme sequence
indicator shows the current programme phase,
running from top to bottom through Wash, Rinse,
Spin/Drain.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
for at least 3 seconds.
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
"Service"
Lighting up of the "Service" indication can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use;
if the fault persists, contact our After Sales Service.
for at least
PROGRAMME END
• The light of the programme sequence indicator
is off, and the "Door open" indication
up.
1. Switch the machine off by pushing "On/
Off"
.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
.
1. Press the "Start/Pause" button
the programme. The light flashes.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the "Start/Pause" button
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
.
PROGRAMME BEFORE THE END
The "Drain/Reset" button
programme before the end.
• Press the "Drain/Reset" button
least 3 seconds. Any existing water is drained
out before the door can be opened.
lights
to pause
again. The
cancels a
for at
Whirlpool is a registered trademark of Whirlpool USA
5019 301 06076