Whirlpool Cabrio W10026634B Manuale - Pagina 3

Sfoglia online o scarica il pdf Manuale per Lavatrice Whirlpool Cabrio W10026634B. Whirlpool Cabrio W10026634B 17.

Stampa la pagina
FOR SERVICE TECHNICIAN ONLY – DO NOT REMOVE OR DESTROY
NOTE: Pressing SOIL LEVEL, SPIN SPEED, WATER
LEVEL or LOAD SIZE, and WASH/RINSE TEMP will cause
all indicators above these buttons to toggle on (or off) at
one time.
If any of the following occur during preceding steps, see
TEST #4, page 5:
None of the indicators light up
No beep sound is heard
Some buttons do not light indicators
DEACTIVATION OF DIAGNOSTIC
TEST MODE
Press the STOP, PAUSE/CANCEL, or POWER button
at any time to exit Automatic, Manual, or Console &
Indicators diagnostic test modes.

DISPLAY FAULT/ERROR CODES

EXPLANATION AND
Display
(Saved
RECOMMENDED PROCEDURE
Code)
Long Fill
LF flashes when the water level does not
change for a period of time OR water is
present but control does not detect the water
level changing.
Is water supply connected and turned on?
 
Are hose screens plugged?
 
Is water siphoning out of the drain hose?
 
Check for proper drain hose installation.
Is the pressure hose connection from the tub
 
to the machine/motor control pinched,
kinked, plugged or leaking air?
See TEST #2, page 4.
 
Long Drain
Ld flashes when the water level does not
change after the drain pump is on.
Is the drain hose or the drain pump clogged?
 
Is the drain hose height greater than 96"?
 
Is the pressure hose connection from the tub
 
to the machine/motor control pinched,
kinked, plugged or leaking air?
Is the pump running? If not, see TEST #7,
 
page 6.
Unbalanced Load
uL is displayed when the machine/motor
control detects an off-balance load, and is
steady on while the washer runs a mini-cycle
to rebalance the load.
(none)
Display clears if mini-cycle successfully
 
rebalanced the load.
If the mini-cycle is unsuccessful, uL will
 
flash until the lid is opened, allowing the
customer to view and redistribute the load.
Overloaded
oL flashes when the machine/motor control
detects a load size that exceeds the
washer's capacity OR basket can not
disengage. This may signify:
Load size exceeds washer capacity. Remove
 
excess laundry, then restart cycle.
Mechanical friction on drive mechanism,
 
not allowing the basket to disengage.
P
A
R
T
N
O
.
W
1
0
0
2
6
6
3
4
B
POUR LE TECHNICIEN SEULEMENT – NE PAS ENLEVER NI DÉTRUIRE
EXPLANATION AND
Display
(Saved
RECOMMENDED PROCEDURE
Code)
Suds Detection
Sd is displayed when the machine/motor
control, by analyzing drag on the basket,
detects a suds-lock condition, and is steady on
while the control then runs a mini-clean out
cycle. If the clean out cycle is unable to correct
the over-sudsing problem, the cycle ends and
Sd flashes in the display. This may signify:
Load is bunched or twisted around agitator.
 
Excessive detergent usage.
 
Basket cannot engage during drain step.
 
Mechanical friction on drive mechanism,
 
not allowing basket to engage.
Open/Close Lid
lid flashes when the following conditions
occur:
User presses START with lid open.
 
User presses START after 2 consecutive
 
machine cycles without opening lid.
The machine/motor control cannot detect the
 
lid switch opening and closing properly.
See TEST #8, page 6.
 
Pump Out (lid opened)
Po flashes when drain pump begins pumping
out water from tub upon activation by the
(none)
lid having been left open for more than 10
minutes.
Close lid to stop drain pump.
 
Hot, Cold Reversed
HC flashes when the hot and cold inlet hoses
are reversed.
Make sure inlet hoses are connected
 
(none)
correctly.
If hoses are installed properly, Automatic
 
Temperature Control may be stuck in low
resistance range. See Test #5, page 5.
Lid Lock Failure
dL flashes if the following conditions occur:
Lid is not closed completely due to
 
interference.
Check for lock interference with lid or lock
 
bezel.
Wash media buildup is preventing the lock
 
bolt from extending.
Machine/motor control detects open lid
 
switch when attempting to lock.
Machine/motor control cannot determine if
 
lid lock is in a locked state.
See TEST #8, page 6.
 
Lid Unlock Failure
dU flashes if the following conditions occur:
Excessive force on lid is preventing lock bolt
 
from retracting.
Wash media buildup is preventing lock bolt
 
from retracting.
Machine/motor control cannot determine if
 
lid lock is in an unlocked state.
See TEST #8, page 6.
 
P
A
G
E
3
EXPLANATION AND
Display
(Saved
RECOMMENDED PROCEDURE
Code)
Pressure Signal Out-of-Range
F then 1 flashes when the control detects an
out of range pressure signal.
Check pressure hose connection from tub
 
to machine/motor control. Is hose pinched,
kinked, plugged or leaking air?
If F then 1 repeats numerous times after
 
POWER is pressed and the pressure hose
connection is not pinched or kinked,
replace the machine/motor control.
Keypad/User Interface Failure
F then 2 flashes when in:
Diagnostic Test mode if a stuck key is
 
detected.
Standby mode if there is a user interface
 
mismatch.
See TEST #4, page 5.
 
ATC Thermistor Open/Short
F then 40 flashes when the ATC Thermistor is
detected to be open or shorted.
See TEST #5, page 5.
 
Motor RPS Thermistor Open/Short
F then 41 flashes when the motor rotor
position sensor (RPS) thermistor is detected to
be open or shorted.
See TEST #3, page 4.
 
NOTE: This error code is only displayed when
viewing saved fault codes.
See Diagnostic Test, page 1, for accessing
 
saved fault codes.
Heater in unknown state
F then 42 flashes when the control cannot
detect if the heater is ON or OFF.
See TEST #9, page 6.
 
Heater is continuously ON
F then 43 flashes when the heater is ON when
it should be OFF.
See TEST #9, page 6.
 
Heater cannot be turned ON
F then 44 flashes when the heater has been
turned ON by the control, but the control
cannot detect that the heater is ON.
See TEST #9, page 6.
 
Motor Stalled
F then 50 flashes when the motor rotor
position sensor (RPS) senses no rotation.
Does basket turn freely? If not, make sure
 
bottom shipping pack has been removed.
Determine cause of friction.
If basket turns freely, see TEST #3, page 4.
 
Motor RPS Failure
F then 51 flashes when there is a motor rotor
position sensor (RPS) failure or lower harness
problem.
See TEST #3, page 4.
 
Motor Stop Failure
F then 52 flashes when the motor rotor position
sensor (RPS) senses rotation after Stop
command.
See TEST #3, page 4.
 
P
È I
C
E
N
o
W10026634B