Whirlpool 3406449 Manuale di istruzioni per l'installazione - Pagina 6

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Asciugatrice Whirlpool 3406449. Whirlpool 3406449 12. Commercial 27" electronic dryer

Stampa la pagina

Electrical

requirements

If codes

permit

and a separate

ground

wire is used, it is

recommended

that a qualified

electrician

determine

that the ground

path is adequate.

Important:

Observe

all governing

codes and ordinances.

A four-wire

or three-wire,

single-phase,

120/240-volt,

60-Hz, AC-only

electrical

supply (or four-wire

or three-wire,

120/208-volt,

if specified

on the

model/serial

rating plate)

is required

on a separate,

30-ampere

circuit,

fused on both sides of the line. A

time-delay

fuse or circuit

breaker

recommended.

The model/serial

rating plate

is located

in the door

well behind

the dryer door on the

front of the opening.

A wiring diagram

is located

inside the

console

or on back panel

of dryer.

It is the personal

responsibility

and

obligation

of the customer

to contact

a qualified

electrician

to assure that

the electrical

installation

is adequate

and in conformance

with the

National

Electrical

Code, ANSI/NFPA

70 -

latest edition*,

and all local

codes

and ordinances.

Copies of the standards listed above may

be obtained from:

National Fire Protection Association

Batterymarch

Park

Quincy, Massachusetts 02269

Power supply cord

Use a new 30-amp

power supply

cord.

Local codes

may permit

the use of a

U.L.-listed, 120/240-volt

minimum,

30-

ampere,

dryer power

supply cord kit

(pigtail).

Power supply cord should be

Type SRD or SRDT and be at least four

feet long. The wires that connect

the dryer must end with ring terminals

or spade

terminals

with upturned

ends.

A 3/4", U.L.-listed strain relief must be

installed

where

the power

supply cord

connects

to the dryer (see Figures 2

and 3).

spade

----

terminals with

upturned ends

strain relief \

(whtte)

NEUTRAL

grbund prong

Four-wire

power

supply

cord

NEMA 14-30P

Figure

&!i%zq$

This blade connected

terminal

NEUTRAL /to

this conductor.\

(white or cente

Three-wire

power supply

cord

NEMA lo-30P

Figure

For use where

local codes

permit use of

flexible power

supply cord.

four-wire

receptacle

(14- JOR)

Figure

three-wire

receptacle

(1 O-30R)

Figure

Four-wire

installation

recommended:

The power supply

cord must have four, No.-1 0 copper

wires and match

a four-wire

receptacle

of NEMA Type 14-30R (see

Figure 4). The fourth wire (ground

conductor)

must be identified

with a

green

cover and the neutral

conductor

by a white cover.

Three-wire

installatton

(it a four-wire

system is not available):

The power

supply cord must have three, No.-1 0

copper

wires to match

a three-wire

receptacle

of NEMA Type 1 O-30R (see

Figure 5).

Direct wire

The dryer can be connected

directly

to fused disconnect

or circuit breaker

box with four-wire

or three-wire

flexible

armored

or non-metallic

sheathed

copper

cable

(with ground

wire). Do Not use two-wire

with bare

ground

wire. All current-carrying

wires

must be insulated.

A U.L.-listed conduit

connector

must

be installed

at the junction

box. USE

ONLY lo-GAUGE

SOLID COPPER WIRE.

DO NOT USE ALUMINUM

WIRE. Allow

four feet of slack in the line so dryer

can be moved

if servicing

is ever

necessary.

Page 6