Whirlpool 3LG5706XP Istruzioni per l'installazione - Pagina 4
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Asciugatrice Whirlpool 3LG5706XP. Whirlpool 3LG5706XP 5. Automatic dryers
Anche per Whirlpool 3LG5706XP: Manuale d'uso e manutenzione (12 pagine)
Stampa la pagina
e'
Now start...
.
, ,/fi 2
13
Use a brush and
n
liquid detergent
to test
1 I
Take tape off
of front corners
of dryer.
2
Open dryer and
n
remove the literature
all
gas connections
for leaks. Bubbles
around connections
will indicate
a
leak. If a leak appears,
shut off gas
valve controls and adjust connections.
Then check connections
again
NEVER TEST FOR GAS LEAKS WITH
A FLAME
14
Connect the
H grounding
wire to the
holes by hand. A little liquid detergent
to lubricate
the screw will help. Use a 1"
wrench or socket to finish turning the
legs until you reach the diamond
mark.
and parts packages.
(If your dryer has
a drying rack it should be removed
also.) Remove all parts from the plastic
packages,
Line these up next to your
tools so each part is there when you
need it.
Check to see that you hove these parts:
4 legs
1 grounding
wire
literature rack
external groinding
connector
on the buck of the dryer. Connect the
other end of the grounding
wire
to a grounded
cold water pipe. Plug
the electrical
cord into the
grounded
outlet.
15
Turn the
n
dryer onto
remove air from the
gas supply line. Using a
full heat cycle (not the
air cycle], let the dryer run for at
least five minutes. If the burner does not
ignite and you can feel no heat inside
the dryer, shut off the dryer for five
minutes. Check that all supply valve
controls are in "ON" position and
that the electrical
cord is plugged
in.
Repeat the five-minute
test.
,
/
8.
Move the dryer close to its final
location. To make sure the dryer is level,
take a carpenter's
level and place it
on the top of the dryer, first side to side,
then front to back. If the dryer is not
level, screw the legs of the dryer up or
down to adjust.
3
Remove the tape that holds
H the drum to the cabinet.
(Some dryer drums are not taped for
shipping.)
Move the drum by hand
to make certain all tape has been
removed. Wipe the interior of the
drum thoroughly
with a damp cloth
before using the dryer.
see Exhaust
Requirements.
Connect
exhaust
duct to exhaust
hood. Use duct
Use caulking
corr
9.
I
I-
Remove the red cap from the the
gas pipe, Move the dryer into its final
position.
seal exterior wall opening
around
exhaust hood.
I lo
Connect gas supply to dryer.
\
Use pipe joint compound
m resistant to the action of
LP gas for gas connections.
17,
Install the
literature rack.
-y
If flexible metal tubing is
Insert tabs (2
on each side
and 2 on the
bottom] into the
back of the dryer
console. Gently
push in and dowr
the carton and place them on the floor
in back of the dryer.
5
n
Firmly grasp the
bodv of the drver and
I I
tabs lock in place.
The gas valve
--
inside the drver is
gently lay it on its back'on the
cardboard
corners.
-
6
With one of the
<
n
legs in hand,
t
shipped
in the "ON" position. Check
that the gas valve shut - off control is still
in the "ON" positio
12,
Open the shut-off valve in the gas
supply line.
Check to see that all of the parts you
removed from the installation
parts
packages
in step
2
are now
installed
in the dryer, If you still have an extra
part, go back through the steps to see
what you skipped.
check the ridges for a
diamond
marking, that's
how far the leg is
supposed to go into
" 7
the hole. Start to screw the legs into the
19
Check to make sure
m you have all the tools
you started with in step A
Congratulatfions!
You have just finished
installing
your new Whirlpool
gas dryer. To make sure you get
the most efficient
use
and greatest
en)oyment
from your new dryer, read
your Whirlpool
Operating
Instructions.
(And be sure to fold
these Installation
instructions
and put
them in the literature
Bat-Pak.
They'll make re-installing
your
Whlrlpool dryer in another
home as easy as your first
installation.)
J
PANEL
C