Whirlpool YCEE2760KQ1 Manuale di istruzioni per l'installazione - Pagina 6
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Asciugatrice Whirlpool YCEE2760KQ1. Whirlpool YCEE2760KQ1 27. Commercial dryer gas or electric
Stampa la pagina
Now Start...
With dryer in laundry area.
Excessive Weight Hazard
Use two or more people to move
and install dryer,
Failure to do so can result in
back or other injury.
3-prong,
_
I _
oxhould
vent
I, 1
i fS
1
-" _ I I
gassupplyInne
/
gas shutoff valve
l
mTake tape
off front corners of
dryer, Open dryer and remove
the
literature
and parts packages,
Wipe
the interior of the drum thoroughly
with a damp
cloth,
mTake l_vo of the cardboard
corners from the carton
and place
them on the floor in back of the dryer,
Firmly grasp the body of the dryer
and gently lay it on its back on the
cardboard
corners,
mWith one of the legs in hand,
check
the ridges for a diamond
marking, That's how far the leg is
supposed
to go into the hole,
mStaff to screw the leveling
legs
into the holes by hand, (Use a small
amount
of liquid detergent
to
lubricate
the screw threads
so it is
easier to turn the legs,) Use a 1-inch
wrench
or socket wrench
to finish
turning
the legs until you reach the
diamond
mark,
Now stand the dryer up,
Slide dryer onto cardboard
or
hardboard
before moving across floor
to avoid damaging
floor covering.
m Remove the service door of the
meter case, Lift
the service door
up at the back
and remove,
Install money-
accepting
device,
(Refer to
manufaturer's
instructions
for proper
installation,)
For dryers using coin slides, use
adapter
kit supplied
with dryer,
Replace
the meter case service door,
Put the coin vault with lock and key
the meter
case opening,
m Move dryer close to final
position, Remove
cardboard
or
hardboard
from under dryer,
m Remove
red cap from gas pipe,
Carefully
move dryer into final
position, Place level on top of the
dryer, first side to side; then front to
back, If the dryer is not level, adjust
the legs of the dryer up or down until
the dryer is level,
m Connect
gas supply to dryer,
Use pipe-joint
compound
resistant to
the action
of L,P, gas for gas
connections,
If flexible
metal tubing
is
used, be certain
there are no kinks,
If necessary
for service, open the toe
panel, use a putty knife to press on
the toe panel
lock located
at the
center
top of the toe panel, Pull
downward
on the toe panel
to open,
Toe panel
is hinged
at the bottom,
m Open the shutoff valve in the
gas supply line,
0
• Use a non-corrosive
leak
detection
fluid to check for leaks,
Bubbles around
connections
will
indicate
a leak, If a leak appears,
shut off gas valve controls and adjust
connections,
Then check
connections
again,
Close toe panel,
All connections
must be wrench-
tightened.
1
• To exhaust dryer, see Exhaust
requirements,
Pages 3-4, Connect
exhaust vent system to dryer exhaust
outlet
and exhaust
hood using 4"
(10,2 cm) clamps,
Use caulking
to
seal exterior wall opening
around
exhaust
hood,
2.
Carefully
move dryer into
final position,
Place level on top of
the dryer, first side to side; then front
to back,
If the dryer is not level, adjust
the legs of the dryer up or down
until
the dryer is level,
1 _
• Plug power supply cord
into
grounded
outlet,
14.
Check
dryer operation
(some
accumulated
time may be on the
timer due to factory
testing),
Insert coins in slide and press slide in
slowly, (Operating
time will
accumulate
per number
of coins and
type of timing cam used,) Push
START/RESTARTbutton,
Using a full
heat cycle
(not the air cycle),
let the
dryer run for at least five minutes,
Dryer will stop when time is used up,
Note: Dryer door must be closed for
dryer to operate,
When door is open,
dryer stops, but timer continues
to run,
To restart dryer, close door and push
START/RESTARTbutton,
5
• If the burner does not ignite
and you can feel no heat inside the
dryer, shut off dryer for five minutes,
Check
that all supply valve controls
are in "ON" position
and that the
electrical
cord is plugged
in, Repeat
five-minute
test,
6.
If drying time is too long,
make sure lint screen is clean,
Page 6