Whirlpool YCEP2760KQ2 Manuale di istruzioni per l'installazione - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Asciugatrice Whirlpool YCEP2760KQ2. Whirlpool YCEP2760KQ2 27. Commercial dryer gas or electric

Stampa la pagina

The console

houses the electronic

control

board, The board

is factory

set

for a dry time of 45 minutes,

Consult

the Tech Sheet found

inside the dryer

toe panel

to reset dry time and for

other options,

The coin-slide

mechanism,

control

panel

lock and key, and coin-box

lock

and key are not included

and are

available

from usual industry sources,

Exhaust

requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to do so can result in

death or fire,

Do not use non-metal

flexible vent,

metal vent that is smaller than four

inches in diameter

or exhaust hoods

with magnetic

latches,

The dryer must be exhausted

outdoors,

Do not exhaust

dryer into a gas vent,

chimney,

wall, ceiling,

or concealed

space

of a building,

Do not install flexible vent in enclosed

walls, ceilings or floors,

If using an existing exhaust system,

clean

lint from entire length of exhaust

system, Make sure exhaust hood is not

plugged

with lint,

The exhaust system should be

inspected

and cleaned

yearly,

Replace

any plastic or metal foil

exhaust vent with rigid metal

flexible

metal vent,

Use 4" (10,2 cm) vent clamps to

secure vent system,

exhaust airflow

better

good

_=1

Four-inch (10.2 cm) metal exhaust

vent isrequired,

Plan installation to

use the fewest number

of elbows and

turns,

Metal flexible vent must be fully

extended

and supported when the

dryer is in its final position,

DO NOT

KINK OR CRUSH THE VENT, The metal

flexible vent must be completely

open to allow adequate

exhaust air

to flow.

Allow as much

room as possible

when

using elbows or making turns,

Bend vent gradually

to avoid

kinking,

Remove

excess flexible vent to avoid

sagging

and kinking that may result in

reduced

air flow,

Exhaust outlet is located

at the

center

of the boftom

dryer back,

The exhaust vent can be routed up,

down,

left, right, behind the dryer or

straight out the back of the dryer,

Maximum

length of exhaust system

depends

upon the type of vent used,

number

of elbows and type of

exhaust hood, The maximum

length

for both rigid and flexible vent is

shown in the chart,

EXHAUSTHOOD TYPE

4 _

.o,

of 90°

turm

(10= c_

1_ c_)

MAXIMUM LENGTH OF &-INCH (I 0.2 cm) DIAMEilER

RIGIDMETAL VENT

64 FT. ( 19.5m) 64 FT. ( 19.5m)

58FT. ( 17.7 m)

54 FT. ( 16.5m) 54 FT. ( 16.5m)

48FT. ( 14.6 m)

44 FT.(13.4 m)

44 FT.(13"4 m)

38 FT.(11.6 m)

35 FT. ( 10.7m) 35 FT. ( 10.7m)

29FT. ( 8.8 m)

27 FT.

( 8.2 m)

27FT.

( 8.2 m)

21FT.

( 6,4 m)

MAXIMUM

LENG1H

OF 4-INCH ( 10.2 cm) D IAMElSR

F LI'_(IBLE

MErAL VENT

36 FT.(11.0 m)

36 FT.(ll.a m)

28 FT.(8.5 m)

31 FT.(9.4 m)

31 FT.(9"4 nO

23 FT.(7.0 m)

27FT. ( 8.2 m)

19FT. ( 5.8 m)

25 FT.(7.6 m)

28 FT.(7.6 nO

17 FT.(5.2 m)

23FT. ( 7.a m)

23 FT.(7.0 nO

18 FT.(4.6 m)

For exhaust systems not covered

the exhaust

length chart, see

Whirlpool

Service Manual,

"Exhausting

Whirlpool

Dryers," Part No, 603197,

available

from your Whirlpool

parts

distributor,

The dryer must be exhausted

to the

outside and provision made

for

enough airforcombustion and

ventilation, (Check governing codes

and ordinances,)

See °Recessed

area

and closet installation

instructions"

Page 12,

An exhaust hood should cap the

exhaust vent to prevent

exhausted

air

from returning

into the dryer, The

outlet

of the hood must be at least

12 inches (30,5 cm) from the ground

or anything

else that may be in the

path of the exhaust,

Four-inch o utlet h ood is preferred.

However,a 2-I 12-inch ( 6,4 cm) outlet

exhausthood may be used,A

2-I/2-inch (6,4 cm) outlet c reates

greaterback pressure t han other

hood types, Forpermanent

installation,

a stationary exhaust

systemis required,

Page 3