Whirlpool YWED9500TU0 Manuale d'uso e manutenzione - Pagina 20
Sfoglia online o scarica il pdf Manuale d'uso e manutenzione per Asciugatrice Whirlpool YWED9500TU0. Whirlpool YWED9500TU0 44. Electronic electric dryer
Anche per Whirlpool YWED9500TU0: Manuale (17 pagine)
Stampa la pagina
Dryerdisplaying codemessage
•
"PF" (power failure), check the following:
Was the drying cycle interrupted
by a power failure?
Press and hold START to restart the dryer.
•
"E" Variable (El, E2, E3) service codes:
Call for service.
"L2" Diagnostic Code. The drum will turn, but there may
be a problem with your home power supply keeping the
dryer's heater from turning on.
Check the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or
breakers. Replace the fuse or reset the circuit breaker.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, consult a qualified electrician.
The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display. The
Estimated Time Remaining will return on the display.
"AF" Diagnostic Code. The dryer vent may be crushed or
blocked.
Check the following:
Check to see if the vent run from the dryer to the wall is
crushed.
Confirm the vent run from the dryer to the wall is free of lint
and debris.
Confirm the exterior vent exhaust hood is free of lint and
debris.
Confirm your vent system falls within the recommended
run
length and number of elbows for the type of vent you are
using. Refer to "Plan Vent System" for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, have your entire home venting run
cleaned.
The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display. The
Estimated Time Remaining will return on the display.
Clothes are not drying satisfactorily, drying times are too
long, or load is too hot
•
Is the lint screen clogged
with lint?
Lint screen should be cleaned before each load.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow
these instructions can result in death
or fire.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement.
If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
Installation Instructions.
Are fabric softener sheets blocking the grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct
length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
•
Is the exhaust vent diameter the correct size?
Use 4" (10.2 cm) diameter vent material.
Explosion
Hazard
Keep flammable
materials
and vapors,
such as
gasoline,
away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion,
or fire.
Is the dryer located in a room with temperature
below
45°F (7°C)?
Proper operation of dryer cycles requires temperatures
above
45°F (7°C).
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (2.5 cm) of airspace, and, for most installations, the rear
of the dryer requires 5" (12.7 cm). See the Installation
Instructions.
Has the Air Only temperature
setting been selected?
Select the right temperature for the types of garments being
dried. See "Additional Features."
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
20