Whirlpool 36'' Freestanding Gas Range Manuale di istruzioni per l'installazione - Pagina 4

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Cappa di ventilazione Whirlpool 36'' Freestanding Gas Range. Whirlpool 36'' Freestanding Gas Range 6. 30" and 36" gas sealed burner cooktop
Anche per Whirlpool 36'' Freestanding Gas Range: Manuale di istruzioni per l'installazione (13 pagine), Manuale di istruzioni per l'installazione (10 pagine), Manuale di istruzioni per l'installazione (7 pagine), Manuale di istruzioni per l'installazione (7 pagine), Istruzioni per l'installazione e manuale d'uso e manutenzione (28 pagine), Manuale di istruzioni per l'installazione (28 pagine), Manuale di istruzioni per l'installazione (7 pagine), Istruzioni per l'installazione (5 pagine)

Stampa la pagina
Whirlpool 36'' Freestanding Gas Range Manuale di istruzioni per l'installazione
C.
Locate
rear mounting
holes
Fasten
rear of burner
box
using one screw
and
washer
in each
of
the hue rear mounting
holes that
will
best secure
the cooktop
to the
countertop.
Note:
Hand
tighten
screws
only until
outer
Ilp of burner
box is snug to
COuntertOp.
OVefliQhtenlnQ
may
cause
damage
to cooktop
7
If cutout dimenslons are too large
W or screws cannot be used with
countertop
material
(such OS ceramlc):
a.
Remove
washers
and
bolts
from parts
bag.
Place
a washer
over each
bolt with the grooved
side of
washerfacing
away
from bolt head
Place
one bolt and
washer
into each
of
the outermost
front mounting
holes
d
Luff cooktop
slightly
and
push
8
back,
lowering
cooktop
into
proper
positlon
b
Lifl top of cwktop
Slightly
and
n
release
support
red Pull
cooktop
forward
until hinges
lock
Lower
cooktop.
c.
Locate
rear
mounting
holes.
Place
one bolt and
cup washer
Into each
of the two outermost
rear
mounting
holes. Remove
cooktop
from
countertop
cutout.
d
Lock each
bolt and
washer
in
.
place
using
a flat washer
and
hex nut on the bottom
side of the burner
e.
Reset cooktop
in countertop
opening
Center
the burner
box in the cutout
Check
that
front edge
of burner
box is parallel
to edge
of
countertop.
f.
Working
below
the countertop.
slide a IockinQ
plate
over the
lower
end of each
corner
bolt
Fasten
each
bolt in olace
with a tubular
nut. The
&king
plate
must make
contact
with as
much
of the countertop
as possible
Tighten
each
tubular
nut by hand
until
outer
lip of burner
box is SnUQ to
countertop.
Do
not
overtighten
to
prevent
damage
to CoUnterfOp.
8
Make
electrical
connections.
n
See Electrical
requirements
and
Electrical
connection
sections.
Panels
A and
EI, for details.
9
Replace
front drip bowls
and
n
surface
elements.
Place
dnp pan
I" griddle
I opening.
Insert electric
element.
Place
griddle
over element.
Place
cover
over griddle.
[
Congratditions!
1