Whirlpool GZ5730 Series Istruzioni per l'installazione e manuale d'uso e manutenzione - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso e manutenzione per Cappa di ventilazione Whirlpool GZ5730 Series. Whirlpool GZ5730 Series 21. 30" (76.2 cm) and 36" (91.4 cm) convertible range hood

Stampa la pagina

Before you start...

Your safety and the safety of

others is very important.

We have provided many important

safety messages in this manual and

on your appliance. Always read and

obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to

potential hazards that can kill

or hurt you and others. All safety

messages will follow the safety alert

symbol and either the word "DANGER"

or "WARNING". These words mean:

DANGER

You can be killed or seriously injured

if you don't immediately follow

instructions.

WARNING

You can be killed or seriously injured

if you don't follow instructions.

All safety messages will tell you what

the potential hazard is, tell you how to

reduce the chance of injury, and tell

you what can happen if the

instructions are not followed.

Important: Observe all governing

codes and ordinances.

Proper installation is your

responsibility. Make sure you have

everything necessary for correct

installation. It is the responsibility of

the installer to comply with the

clearances specified.

Check the location where the range

hood will be installed. The location

should be away from strong draft

areas, such as windows, doors, and

strong heating vents.

Mobile home installation

The installation of this range hood

must conform to the Manufactured

Home Construction Safety

Standards, Title 24 CFR, Part 328

(formerly the Federal Standard for

Mobile Home Construction and

Safety, Title 24, HUD, Part 280) or

when such standard is not

applicable, the Standard for

Manufactured Home Installation

1982 (Manufactured Home Sites,

Communities and Setups) ANSI

A225.1/NFPA 501A*, or latest edition,

or with local codes.

WARNING — TO REDUCE THE

RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO

PERSONS, OBSERVE THE

FOLLOWING:

Installation work and electrical

wiring must be done by qualified

person(s) in accordance with all

applicable Codes and Standards,

including Fire Rated

Construction. Sufficient air is

needed for proper combustion

and exhausting of gases through

the flue (chimney) of fuel burning

equipment to prevent back

drafting. Follow the heating

equipment manufacturer's

guideline and safety standards

such as those published by the

National Fire Protection

Association (NFPA), and the

American Society of Heating

Refrigeration and Air

Conditioning Engineers

(ASHRAE), and the local code

authorities.

When cutting or drilling into wall or

ceiling, do not damage electrical

wiring and other hidden utilities.

Ducted fans must always be

vented to the outdoors.

WARNING — To reduce the risk

of fire, use only metal ductwork.

This unit must be grounded.

This hood is factory set for vented

installations. For non-vented

installations, purchase 30"

(76.2 cm) Filter Kit No. 4396291

or 36" (91.4 cm) Filter Kit No.

4396292 from your dealer.

Tools and

materials needed

for installation:

• compass or 8" (20.3 cm) circle template

• flat blade screwdriver

• Phillips screwdriver

• pliers

• metal snips

• drill

• 1-1/4" (3.0 cm) drill bit

• pencil

• ruler

• keyhole saw

• saber saw

• duct tape

• 7" (17.8 cm) round damper if using

7" (17.8 cm) round vent system

Electrical

requirements

Important: Observe all governing

codes and ordinances.

It is the customer's responsibility:

• To contact a qualified electrical

installer.

• To assure that the electrical

installation is adequate and in

conformance with National

Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA

Standards C22.1-94, Canadian

Electrical Code, Part 1 and

C22.2 No.0-M91 - latest

edition** and all local codes

and ordinances.

A separate ground wire must be

used. It is recommended that a

qualified electrician determine that

the ground path is adequate.

A 120-volt, 60-Hz, AC-only, fused

electrical system is required. A

separate 15-amp circuit is

recommended.

Do not ground to a gas pipe.

Check with a qualified electrician if

you are not sure range hood is

properly grounded.

Do not have a fuse in the neutral or

ground circuit.

IMPORTANT:

Save Installation Instructions for

electrical inspector's use.

The range hood must be connected

with copper wire only.

The range hood should be

connected directly to the fused

disconnect (or circuit breaker) box

through flexible armored or

nonmetallic sheathed copper cable.

A U.L.- or C.S.A.-listed strain relief

must be provided at each end of the

power supply cable. Wire sizes

(COPPER WIRE ONLY) and

connections must conform with the

rating of the appliance as specified

on the model/serial rating plate.

Wire sizes must conform to the

requirements of the National

Electrical Code ANSI/NFPA 70 —

latest edition*, or CSA Standards

C22.1-94, Canadian Electrical Code

Part 1 and C22.2 No. 0-M91 - latest

edition** and all local codes and

ordinances.