Whirlpool LI3Y5B Istruzioni per l'installazione e manuale d'uso e manutenzione - Pagina 4
Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso e manutenzione per Cappa di ventilazione Whirlpool LI3Y5B. Whirlpool LI3Y5B 28. 30 inch (76.2 cm) range hood
Stampa la pagina
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■ D rill
■ 1 ¼" (3.0 cm) drill bit
⁄
" (3.0 mm) drill bit for pilot holes
1
■
8
■ P encil
■ W ire stripper or utility knife
■ T ape measure or ruler
■ C aulking gun and weatherproof caulking compound
■ F lat-blade screwdriver
■ P hillips screwdriver
■ S aber or keyhole saw
■ V ent clamps
■ M etal snips
■ C ompass or 8" (20.3 cm) circle template
Parts supplied
Remove parts from package. Check that all parts are included.
■ 2 - Metal filters
■ 6 - 3.5 x 9.5 mm mounting screws
■ 3 - 4.5 x 13 mm damper screws
■ 3 ¼" x 10" (8.3 x 25.4 cm) damper/vent connector
■ T -20 Torx®† adapter
Parts needed
■ 3 ¼" x 10" (8.3 x 25.4 cm) or 6" (15.2 cm) or larger round metal
venting
■ 6 " (15.2 cm) or larger round damper, if using 6" (15.2 cm) or
larger round vent system
■ 3 ¼" x 10" (8.3 x 25.4 cm) to 6" (15.2 cm) or larger diameter
transition piece if using 6" (15.2 cm) or larger diameter round
vent system.
■ 3 - UL listed wire connectors
For cabinets with recessed bottoms:
■ T wo 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
■ F our flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
®†TORX is a registered trademark of Acument Intellectual Properties, LLC
4
INSTALLATION REQUIREMENTS
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■ I t is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located inside the range hood on
the left wall.
■ R ange hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
■ C abinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.
■ G rounded electrical outlet is required. See "Electrical
Requirements" section.
■ T he hood is factory-set for vented installations.
■ A ll openings in ceiling and wall where range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24 CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, title 24, HUD, Part 280)
or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or
latest edition, or with local codes.
Product Dimensions
1³⁄₄"
(4.4 cm)
4³⁄₄"
(12.1 cm)
³⁄₄"
(2.0 cm)
29¹⁵⁄₁₆" (76.0 cm)
4¹⁄₁₆" (10.3 cm)
1"
(2.5 cm)
9"
(22.9 cm)
1¹⁄₂"
20"
(3.8 cm)
(50.8 cm)