Whirlpool RH4830XLT1 Manuale d'uso e manutenzione - Pagina 2
Sfoglia online o scarica il pdf Manuale d'uso e manutenzione per Cappa di ventilazione Whirlpool RH4830XLT1. Whirlpool RH4830XLT1 10. 30/36" (76.2/91.4 cm) convertible range hood installation instructions
Anche per Whirlpool RH4830XLT1: Elenco delle parti (1 pagine)
Stampa la pagina
Yoursafetyandthe safetyof
othersis very important.
Wehave provided many i mportant
safety m essages
inthismanual and
onyour a ppliance. Always r ead and
obey atl s afety m essages.
This isthesafety a lert s ymbol.
This symbol alerts y outo
potential hazards thatcankill
orhurtyouandothers. Alisafety
messages
wiiifoliow thesafety a lert
symbol and either t heword "DANGER"
or"WARNING".
These w ords mean:
You Ganbe killed or seri0usly injured
if you don't f011owinstructions.
AIi safety messages wili teli you what
the potentiai hazard is, teii you how to
reduce the chance of injury, and tell
you what can happen if the
instructions are not followed.
important:
Observe
all governing
codes and ordinances.
Proper instaUadon
is your
responsibility.
Make sure you have
everything
necessary for correct
instaUation,
It is the responsibility
of
the installer
to comply
with the
clearances
specified.
Check the location where the range
hood will be instalbd.The
location
should
be away from strong draft
areas, such as windows,
doors, and
strong heating vents.
Mobile home installation
The installation
of this range hood
must conform
to the Manufactured
Home Construction
Safety
Standards, Titb 24 CFR, Part 328
(formerly
the Federal Standard
for
Mobile
Home Construction
and
Safety, Title 24, HUD, Part 280 or
when such standard
is not
applicable,
the Standard
for
Manufactured
Home Installation
1982 (Manufactured
Home Sites,
Communities
and Setups) ANSi
A225.1/NFPA 501A*, or latest edition,
or with local codes.
WARNING -- TO REDUCE THE
RiSK OF FIRE, ELECTRIC
SHOCK, OR iNJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
Installation work and electrical
wiring
must be done by qualified
person(s) in accordance with all
applicable
Codes and Standards,
including
Fire Rated Construction.
Sufficient
air is needed for proper
combustion
and exhausting
of
gases through
the flue (chimney)
of fuel burning equipment
to
prevent back drafting.
Follow the
heating equipment
manufacturer's
guideline and
safety standards such as those
published
by the National Fire
Protection Association
(NFPA),
and the American
Society of
Heating Refrigeration
and Air
Conditioning
Engineers
(ASHRAE), and the local code
authorities.
When cutting or drilling into wall or
ceiling, do not damage electrical
wiring and other hidden utilities.
Ducted fans must always be
vented to the outdoors.
WARNING -- To reduce the risk
of fire, use only metal ductwork.
This unit must be grounded.
This hood is factory set for vented
installations. For non=vented
installations,
purchase Filter Kit
No. 4396388 from your dealer.
Tools and
materials needed
for installation:
fiat hmade
_ 14/4"
(3.0 cm}
screwdriver
drill hit
pmiers
_ I/8"
(or 3 fatal drill
drill
bit for pilot homes
ruiner
_ pencil
For vented installations,
you amso need:
compass or 8"
• duct tape
120.3 era} eircme
" 7" 117.8era) round
terapmate
damper if using
• raetamsnips
7" 117.8era) round
• keyhome saw
vent system
® saber
saw
Cabinets with
recessed bottoms:
2, 2" 15.8 era} wide filler strips. Length and
thickness
determined
by recess diraensions.
4 wood screws or fiat head raachine screws
with washers and nnts to attach filler strips.
Parts supplied:
amurainura mesh filter
* baffle pmateIvented installations}
_3-1/4"× 10"18.3 x25.4era)
damper/vent
connector
parts hag
7" 117.8era} round adapter
important: Observe all governing
codes and ordinances.
it is the customer's
responsibility:
,, To contact a qualified electrical
installer.
• To assure that the electrical
installation is adequate and in
conformance
with National
Electrical Code, ANSI/NFPA 70
-- latest edition*,
or CSA
Standards C22.1-94, Canadian
Electrical Code, Part 1 and
C22.2 No,O=M91 =latest
edition**
and all local codes
and ordinances.
A separate ground wire must be
used. it is recommended
that a
qualified electrician determine that
the ground path is adequate.
A 120-volt, 60-Hz, AS-only, fused
electrical system is required. A
separate 15=amp circuit is
recommended.
Do not ground to a gas pipe.
Check with a qualified electrician if
you are not sure range hood is
properly grounded.
Do not have a fuse in the neutral or
ground circuit.
IMPORTANT:
Save installation instructions for
electrical inspector's use.
The range hood must be connected
with copper wire only.
The range hood should be
connected directly to the fused
disconnect (or circuit breaker) box
through flexible armored or
nonmetallic
sheathed copper cable.
A U.L.° or C.S.A.=listed strain relief
must be provided at each end of the
power supply cable. Wire sizes
(COPPER WIRE ONLY) and
connections
must conform with the
rating of the appliance as specified
on the model/serial
rating plate.