Whirlpool RJH 3330-1 Manuale di installazione e istruzioni per l'uso - Pagina 4
Sfoglia online o scarica il pdf Manuale di installazione e istruzioni per l'uso per Cappa di ventilazione Whirlpool RJH 3330-1. Whirlpool RJH 3330-1 6. Whirlpool microshelf hood installation and operating instructions rjh 3330-1
Stampa la pagina
1.
Connect
the appliance
to the junction
box
through
flexible
armoured
or
nonmetallic
sheathed
copper
cable
(with
ground
wire).
A
suitable
strain relief must be provided
at each end
of the power supply cable (at appliance
and at the
junction
box). See Figure 8.
2.
This appliance
is equipped
with copper
lead
wires. If connection
is made to aluminum
house
wiring,
use only
special
connectors
which
are
approved
for joining
copper and aluminum
wires
in accordance
with the National
Electrical
Code
and local codes and ordinances.
Electrical
Ground
is Required
on This Appliance
Recommended
Electrical
Connection
and Groundrng
Method
This appliance
must be permanently
grounded
in
accordance
with the National
Electrical
Code and
local codes and ordinances.
TO
20
AMP
FUSED
DISCONNECT
(WIRING
DONE
ACCORDING
TO
NATIONAL
ELECTRICAL
CODE
__
AND
APPLICABLE
LOCAL
CODES)
RECEPTACLE7
H
CONNECTION)
LEADING
TO
SWITCHES
I
\GROUND
SCREW
I
I
I
I
I
TERMINAL
ACCESS
COVER
Figure 8
1.
Remove the terminal
access cover. See Fig. 8.
2.
Install
a strain
relief into the opening
of the
wire junction
box. See Figure 8.
3.
Connect
the white
and black
wires
of the
power supply
cable to the white
and black wire
leads inside the terminal
access box. See Figure 8.
4.
Connect
the green ground wire from the power
supply
cable to the end of the green ground wire
provided
in the terminal
access box. See Figure 8.
5.
Replace the terminal
access cover.
Alternate
Grounding
Method
If
the
recommended
grounding
method
is
impossible,
permanently
ground
the appliance
from the green ground wire (located in the terminal
access box) to a grounded
cold water pipe* using a
separate,
green
colored,
insulated
copper
conductor
of appropriate
size (no. 16 minimum).
THIS, HOWEVER,
IS NOT RECOMMENDED.
Do
not ground to a gas supply pipe. Do not connect to
electrical
supply
until
appliance
is permanently
grounded.
*Cold water pipe must have metal continuity
to
electrical
ground and not be interrupted
by plastic,
rubber or other electrically
insulating
connectors
(including
water meter or pump) without
adding a
jumper wire to these connections.
C.
INSTALLING
AND
LEVELING
THE
MICROWAVE
OVEN.
1.
Remove
the screw
from the upper
left
hand side of the microwave
oven. See Figure
9.
2.
Screw the safety bracket to the back of the
microwave
with
the screw
removed
in the
previous
step.
SCREW REMOVED FROM
/
Figure 9
3.
Place the empty hood carton the top of the
cooktop.
Test the shelf hood for strength.
If
the mounting
seems secure,
proceed
to the
next step.
4.
WARNING:
THE
WEIGHT
OF
THE
MICROWAVE
OVEN
MAY EXCEED
YOUR
LIFTING
ABILITY.
ASSISTANCE.
7 I(
I
SHELF
HOOD
SHELF
HOOD
\yy##y-F
'Is
\
HANGING
ANGLE
SHELF
SHELF
HOOD
HOOD
BACK
BACK
LEVELING
LEVELING
BOLTS
BOLTS
Figure 10
w
Page 4
WE
RECOMMEND