Whirlpool WVW75UC6DS Istruzioni per l'installazione e manuale d'uso e manutenzione - Pagina 4

Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso e manutenzione per Cappa di ventilazione Whirlpool WVW75UC6DS. Whirlpool WVW75UC6DS 32. 36" (91.4 cm) island-mount canopy range hood
Anche per Whirlpool WVW75UC6DS: Manuale d'uso e manutenzione Istruzioni per l'installazione (28 pagine), Istruzioni per l'installazione e manuale d'uso e manutenzione (28 pagine)

Stampa la pagina

Whirlpool WVW75UC6DS Istruzioni per l'installazione e manuale d'uso e manutenzione

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

Level

■

Drill with 1

" (3.2 cm), 3/8" (9.5 mm), 1/8" (3.2 mm), and

■

7/64" (2.75 mm) drill bits

Pilot hole drill bits (determined by chimney support

■

attachment method)

Pencil

■

Wire stripper or utility knife

■

Tape measure or ruler

■

Pliers

■

Caulking gun and weatherproof caulking compound

■

Vent clamps

■

Jigsaw or keyhole saw

■

Flat-blade screwdriver

■

Metal snips

■

Phillips screwdriver

■

Parts Needed

Home power supply cable

■

1/2" (12.7 mm) UL listed or CSA approved strain relief

■

3 UL listed wire connectors

■

For Vented Installations, You Will Also Need:

1 wall or roof cap

■

Metal vent system

■

For Non-Vented (Recirculating) Installations,

You Will Also Need:

Recirculation Kit Part Number W10680067 for non-vented

■

(recirculating) installations only. See "Assistance or Service"

section to order.

6" (15.2 cm) diameter round metal vent duct -

■

length required is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

Hood ventilator assembly with canopy glass, retainer

■

brackets, rubber seals, and LED lights installed

Metal grease filter

■

60 - 4.2 x 8 mm screws

■

4 - 3.5 x 6.5 mm screws

■

4 - 5 x 45 mm screws

■

2 - 2.9 x 3 mm screws

■

2 - Leveling screws

■

2 - Nuts

■

INSTALLATION REQUIREMENTS

T10 Torx

adapter

®†

■

T20

Torx

adapter

®†

■

2 - Upper vent covers

■

2 - Lower vent covers

■

4 - Plastic vent clips

■

Mounting template

■

Upper horizontal support bracket

■

Horizontal support

■

8 - Vertical supports

■

Vent transition with back draft damper installed

■

2 - 3.5 x 9.5 mm mounting screws

■

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/

rating plate is located behind the left filter on the rear wall

of the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

Grounded electrical supply is required. See "Electrical

Requirements" section.

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

For plaster or drywall ceilings, the chimney support must

■

be attached to joists. If this is not possible, you must build

a support structure behind the plaster or drywall. The

support structure must be able to support 80 lbs (36.6 kg).

This range hood is recommended for use with cooktops

with a maximum total rating of 60,000 BTUs or less.

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installation" in "Install Range Hood" section.

Recirculation Kit Part Number W10680067 is available from

your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will

be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A,

or latest edition, or with local codes.

†

TORX and T20

are registered trademarks of Acument Intellectual Properties, LLC.