Yamaha Clavinova CVP-202 Data List - Pagina 15

Sfoglia online o scarica il pdf Data List per Strumento musicale Yamaha Clavinova CVP-202. Yamaha Clavinova CVP-202 39. Yamaha cvp-202: supplementary guide

Stampa la pagina

• Portamento time is fixed to 0 when the PORTAMENTO CONTROL is

used.

• HARMONIC CONTENT applies adjustment to the resonance value that

is set by the voice. This parameter specifies relative change with the

value of 64 producing 0 adjustment. As values get higher the sound

becomes increasingly eccentric. Note that for some voices the effective

parameter range is narrower than the legal parameter range.

• RELEASE TIME applies adjustment to the envelope release time set by

the voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• ATTACK TIME applies adjustment to the envelope attack time set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• BRIGHTNESS applies adjustment to the cut-off frequency set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment. Lower voices produce a softer sound. For some

voices the effective parameter range is narrower than the legal

parameter range.

(3-2) CHANNEL MODE MESSAGES

STATUS

1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

CONTROL NUMBER

0ccccccc

CONTROL VALUE

0vvvvvvv

(3-2-1) ALL SOUND OFF (Receive only)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

Switches off all sound from the channel. Reset Note On and Hold On conditions established

by Channel Messages.

(3-2-2) RESET ALL CONTROLLERS (Receive only)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets controllers as follows.

PITCH BEND CHANGE

0 (Center)

AFTER TOUCH

0 (min.)

MODULATION

0 (min.)

EXPRESSION

127 (max.)

SUSTAIN

0 (off)

SOSTENUTO

0 (off)

SOFT PEDAL

0 (off)

Sets number to null. (Internal data remains unchanged)

NRPN

Sets number to null. (Internal data remains unchanged)

RPN

Resets portamento source note number

PORTAMENT CONTROL

PORTAMENTO

0 (off)

(3-2-3) LOCAL CONTROL (Receive only)

(CONTROL NUMBER = 7AH , DATA VALUE = 0/7FH)

When the DATA VALUE = 7FH, LOCAL ON is activated where playing the keys on the

keyboard will produce sound.

When the DATA VALUE = 0, LOCAL OFF is activated where playing the keys on the

keyboard will not produce any sound.

(3-2-4) ALL NOTES OFF (Receive only)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

Switches off all of the channel's "on" notes. However, any notes being held by SUSTAIN or

SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off.

(3-2-5) OMNI OFF (Receive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same processing as for All Notes Off.

(3-2-6) OMNI ON (Receive only) (CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same processing as for All Notes Off. Omni On is not executed.

(3-2-7) MONO (Receive only) (CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the corresponding

channel will be changed to Mode 4 (m=1).

(3-2-8) POLY (Receive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same processing as for All Sounds Off and the corresponding channel will be changed to

Mode 3.

c = CONTROL NUMBER

v = DATA VALUE

(3-3) REGISTERED PARAMETER NUMBER(RPN)

STATUS

1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

RPN LSB

01100100(64H)

RPN LSB NUMBER

0ppppppp

RPN MSB

01100101(65H)

RPN MSB NUMBER

0qqqqqqq

DATA ENTRY MSB

00000110(06H)

DATA VALUE

0mmmmmmm

DATA ENTRY LSB

00100110(26H)

DATA VALUE

0lllllll

First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

RPN

D.ENTRY

LSB MSB

MSB LSB PARAMETER NAME

00H 00H

mmH —

PITCH BEND SENSITIVITY

01H 00H

mmH llH FINE TUNE

02H 00H

mmH —

COARSE TUNE

7FH 7FH

—

NULL

(3-4) NON-REGISTERED PARAMETER NUMBER(NRPN) (Receive only)

STATUS

1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

NRPN LSB

01100010(62H)

NRPN LSB NUMBER

0ppppppp

NRPN MSB

01100011(63H)

NRPN MSB NUMBER

0qqqqqqq

DATA ENTRY MSB

00000110(06H)

DATA VALUE

0mmmmmmm

First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

NRPN

D.ENTRY

MSB LSB MSB LSB PARAMETER NAME DATA RANGE

01H 08H mmH —

VIBRATO RATE

01H 09H mmH —

VIBRATO DEPTH

01H 0AH mmH —

VIBRATO DELAY

01H 20H mmH —

FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 - 0 - +63)

01H 21H mmH —

FILTER RESONANCE

01H 63H

mmH —

EG ATTACK TIME

01H 64H mmH —

EG DECAY TIME

01H 66H mmH —

EG RELEASE

14H rrH mmH —

DRUM FILTER CUTOFF FREQ. 00H - 40H - 7FH (-64 - 0 - +63)

15H rrH mmH —

DRUM FILTER RESONANCE

16H rrH mmH —

DRUM AEG ATTACK RATE 00H - 40H - 7FH (-64 - 0 - +63)

17H rrH mmH —

DRUM AEG DECAY RATE

18H rrH mmH —

DRUM PITCH COARSE

19H rrH mmH —

DRUM PITCH FINE

1AH rrH mmH —

DRUM LEVEL

1CH rrH mmH —

DRUM PANPOT

1DH rrH mmH —

DRUM REVERB SEND LEVEL 00H - 7FH (0 - max.)

1EH rrH mmH —

DRUM CHORUS SEND LEVEL 00H - 7FH (0 - max.)

1FH rrH mmH —

DRUM VARIATION SEND LEVEL 00H - 7FH (0 - max.)

The MSB 14H-1FH (for drums) message is received when multi-part parameters PART

MODE = DRUMS1...2.

rrH : drum instrument note number

(3-5) SYSTEM REALTIME MESSAGES

(3-5-1) MIDI CLOCK

STATUS

11111000 (F8H)

Transmission: 96 clocks per measure are transmitted.

Reception: If the instrument's clock is set to external, after FAH is received from the external

device the instrument's clock will sync with the 96 beats per measure received from the external

device.

Decides whether the internal clock, or Timing Clocks received via the MIDI IN will be used.

(3-5-2) START

STATUS

11111010 (FAH)

Transmission: Transmitted when instrument's Rhythm or Song playback is started.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will start.

(3-5-3) STOP

STATUS

11111100 (FCH)

Transmission: Transmitted when instrument's Rhythm or Song playback is stopped.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will stop.

p = RPN LSB (refer to the list below)

q = RPN MSB (refer to the list below)

m = Data Value

l = Data Value

DATA RANGE

00H-18H (0 - 24 semitones)

{mmH,llH} = {00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

28H - 40H - 58H (-24 - 0 - +24 semitones)

Clears the current RPN number setting.

Does not change the internal parameter settings.

p = NRPN LSB (refer to the list below)

q = NRPN MSB (refer to the list below)

m = Data Value

00H - 40H - 7FH (-64 - 0 - +63)

00H - 7FH (0 - max.)

00H

,01H - 40H

- 7FH

(random,left - center - right)

CVP-202