Yamaha CP4 Stage Data List - Pagina 36

Sfoglia online o scarica il pdf Data List per Strumento musicale Yamaha CP4 Stage. Yamaha CP4 Stage 43. Stage piano

Stampa la pagina
Yamaha CP4 Stage Data List
(3-1-4) PROGRAM CHANGE
STATUS
1100nnnn (CnH)
PROGRAM NUMBER
0ppppppp
(3-1-5) CHANNEL AFTER TOUCH
STATUS
1101nnnn (DnH)
VALUE
0vvvvvvv
(3-1-6) PITCH BEND CHANGE
STATUS
1110nnnn (EnH)
LSB
0vvvvvvv
MSB
0vvvvvvv
Transmitted with a resolution of 7 bits.
(3-2) CHANNEL MODE MESSAGES
STATUS
1011nnnn (BnH)
CONTROL NUMBER
0ccccccc
CONTROL VALUE
0vvvvvvv
(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)
All the sounds currently played including the channel messages such as note-on and hold-on in a certain
channel are muted when receiving this message.
(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)
Resets the values set for the following controllers.
PITCH BEND CHANGE
0 (center)
MODULATION
0 (minimum)
EXPRESSION
127 (maximum)
FOOT CONTROLLER 1
0 (minimum)
FOOT CONTROLLER 2
0 (minimum)
SUSTAIN SWITCH
0 (off)
SOSTENUTO SWITCH
0 (off)
RPN
Not assigned; No change
Doesn't reset the following data:
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, RELEASE TIME,
ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT1 DEPTH, EFFECT3 DEPTH, PORTAMENTO SWITCH,
PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING
*8 For CP4 STAGE only
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain
or Sostenuto is on, notes will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16,
the channel will be Mode 4 (m = 1).
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode 3.
(3-3) REGISTERED PARAMETER NUMBER
STATUS
1011nnnn (BnH)
LSB
01100100 (64H)
RPN LSB
0ppppppp
MSB
01100101 (65H)
RPN MSB
0qqqqqqq
DATA ENTRY MSB
00000110 (06H)
DATA VALUE
0mmmmmmm
DATA ENTRY LSB
00100110 (26H)
DATA VALUE
0lllllll
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN
D.ENTRY
LSB MSB MSB LSB
PARAMETER NAME
00H 00H mmH ---
PITCH BEND SENSITIVITY
01H 00H mmH llH
MASTER FINE TUNE
02H 00H mmH ---
MASTER COARSE TUNE
7FH 7FH --- ---
RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.
(3-4) NON-REGISTERED PARAMETER NUMBER
There are no applicable parameters.
(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS
11111110 (FEH)
Transmitted at every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the Sustain
Switch are forcibly turned off. Also, the values of the Controllers are reset to the default settings.
n = 0 - 15 CHANNEL NUMBER
p = 0 - 127
n = 0 - 15 CHANNEL NUMBER
v = 0 - 127 AFTER TOUCH VALUE
n = 0 - 15 CHANNEL NUMBER
PITCH BEND CHANGE LSB
PITCH BEND CHANGE MSB
n = 0 - 15 CHANNEL NUMBER
c = CONTROL NUMBER
v = DATA VALUE
n = 0 - 15 CHANNEL NUMBER
p = RPN LSB
(Refer to the table as shown below.)
q = RPN MSB
(Refer to the table as shown below.)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 12 semitones)
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
28H - 40H - 58H (-24 - 0 - +24 semitones)
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
("n" = Device No. However, this instrument receives under "omni.")
(3-6-1-2) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH 06H 00H 00H 00H 7FH F7H
dd = CP4 STAGE: 49, CP40 STAGE: 4A
(3-6-2) PARAMETER CHANGE
(3-6-2-1) NATIVE PARAMETER CHANGE
11110000
F0
01000011
43
0001nnnn
1n
01111111
7F
0*******
**
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0ddddddd
ddddddd
|
|
11110111
F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
See the following MIDI Data Table for Address.
*8
(3-6-3) BULK DUMP
11110000
F0
01000011
43
0000nnnn
0n
01111111
7F
0*******
**
0bbbbbbb
bbbbbbb
0bbbbbbb
bbbbbbb
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0
0
|
|
0ccccccc
ccccccc
11110111
F7
See the following BULK DUMP Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address,
Data and Check sum itself are added.
(3-6-4) DUMP REQUEST
11110000
F0
01000011
43
0010nnnn
2n
01111111
7F
0*******
**
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
11110111
F7
See the following DUMP REQUEST Table for Address and Byte Count.
(3-6-5) PARAMETER REQUEST
11110000
F0
01000011
43
0011nnnn
3n
01111111
7F
0*******
**
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
11110111
F7
See the following MIDI Data Table for Address.
(4) SYSTEM OVERVIEW (Keyboard and Tone Generator)
KBD
Local Sw
TG
KBD
Local Sw
TG
Although two types of note on/note off data, received via MIDI and played on the keyboard will be distinguished, the other
controllers (channel messages) equally affect the entire notes.
ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.
ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.
MIDI Data Format
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
CP4 STAGE: 1A, CP40 STAGE: 1B
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
CP4 STAGE: 1A, CP40 STAGE: 1B
Byte Count
Byte Count
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
CP4 STAGE: 1A, CP40 STAGE: 1B
Address High
Address Mid
Address Low
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
CP4 STAGE: 1A, CP40 STAGE: 1B
Address High
Address Mid
Address Low
End of Exclusive
USB/MIDI = MIDI
To USB
From USB
MIDI Out
MIDI In
USB/MIDI = USB
To USB
From USB
Thru Port
MIDI Out
MIDI In
CP4 STAGE/CP40 STAGE Data List
36