Yamaha PORTATONE PSR-500M Manuale d'uso - Pagina 14
Sfoglia online o scarica il pdf Manuale d'uso per Strumento musicale Yamaha PORTATONE PSR-500M. Yamaha PORTATONE PSR-500M 46.
Stampa la pagina
FEATURE REFERENCE (OVERALL CONTROL)
Setting the Pitch Bend Range
The maximum amount of pitch bend produced by the
PITCH BEND wheel can be set anywhere from +1 semi-
tone to +12 semitones (i.e. plus or minus one octave).
1. To set the pitch bend range, roll the PITCH BEND
wheel all the way in either direction so that the current
range value appears on the MULTI DISPLAY.
PITCH BEND
D
—
wu sen
UER
2. Use the ACCOMP. VOLUME (PITCH BEND
RANGE) [A] and [V] buttons to set the desired range
— the pitch bend range value is displayed in semitones
(-12 through 12). If a minus setting is selected pitch
bend wheel operation is reversed — i.e. roll the wheel
away from you to lower pitch.
pe
BEND RANGE
ACCOMP
VOLUME
0:24
3. Release the PITCH BEND wheel.
* When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a different PAGE
MEMORY is selected.
€ TRANSPOSE
The PSR-500M [TRANSPOSE] buttons makes it possi-
ble to shift the pitch of the PSR-500M up or down in
semitone intervals up to a maximum of 12 semitones (one
octave). Transposing the pitch of the PSR-500M keyboard
makes it easier to play in difficult key signatures, and you
can simply match the pitch of the keyboard to the range of
a singer or other instrumentalist.
STYLE SPUIT VOCE | уосе
и
sme
ЗРЫТУОКЕ
БАТ
TRANS
POSE
42-12
The TRANSPOSE [A] and [V] buttons are used for
transposition. Press the [A] button to increase the pitch of
the keyboard, or the [W] button to lower the pitch. The
selected degree of transposition will be displayed on the
center two digits of the MULTI DISPLAY while the
TRANSPOSE [Å] or [V] button is pressed, and for ap-
proximately 2 seconds after cither TRANSPOSE button is
released.
;
The transposition range is from -12 to +12, with -12
corresponding to downward transposition by 12 semitones
(one octave), and +12 corresponding to upward transposi-
tion by 12 semitones. 0 is the "normal" keyboard pitch
value. The normal transpose value (0) can be recalled at
any time by pressing both the TRANSPOSE [Å] and [F]
buttons at the same time.
* The TRANSPOSE function will not work while any keys are held.
* TRANSPOSE does not affect the percussion voices (numbers
94 through 99).
* When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a different PAGE
MEMORY is selected.
€ TUNING
4
The PSR-500M [TUNING] buttons makes it possible to
tune the pitch of the PSR-500M to match other instru-
ments. Tuning can be accomplished over a +50-cent range
(that's 100 cents total, or one semitone) in 16 steps.
A
tomm
TUNING.
Ч
+ LI
LI
4275
4529 nz
The TUNING [ÀJ] and [V] buttons are used for tuning.
Press the [À] button to raise the pitch of the instrument, or
the [W] button to lower the pitch. The selected degree of
tuning will be shown on the MULTI DISPLAY in Hertz
while the TUNING [A] or [V] button is pressed, and for
approximately 2 seconds after either TUNING button is
released.
The tuning range is from 427.5 Hertz (-50 cents) to
452.9 Hz (+50 cents). 440.0 Hertz (+0 cents) is the "с
mal" tuning value. The normal tuning value (440.0) «
'*
be recalled at any time by pressing both the TUNING [4]
and [V] buttons at the same time.
* TUNING does not affect the percussion voices (numbers 94
through 99).
* When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a different PAGE
MEMORY is selected.
@ TEMPO
The TEMPO buttons control the tempo of the AUTO
ACCOMPANIMENT, the SONG MEMORY, DEMO
playback, and the MULTI PADs.
A
TYLELSPUT VOCE
уос
©
120
=
sme
samvoce
BEAT
4-40-240