Yamaha YSP-5100BL Manuale di riferimento rapido - Pagina 6
Sfoglia online o scarica il pdf Manuale di riferimento rapido per Sistema di altoparlanti Yamaha YSP-5100BL. Yamaha YSP-5100BL 9. Quick reference guide
Stampa la pagina
Carrying out the AUTO SETUP (IntelliBeam)
4
5
Press and hold INTELLIBEAM
for more than 2 seconds.
The INTELLIBEAM key is located inside of the slide cover.
UNIVOLUME
SUR. DECODE INTELLIBEAM
1
2
3
4
5
6
7
8
9
6
Make sure that your listening
room is as quiet as possible.
For accurate measurement, turn off air conditioner or other
devices that make noises.
7
Prepare to leave the room.
The best setting may not be done if you are in the room.
Prepare to leave the room in 10 seconds after pressing ENTER
in step 8.
y
•
When leaving the room, bring this Quick Reference Guide with you.
•
Wait outside the room during the AUTO SETUP procedure.
•
The AUTO SETUP procedure takes about 3 minutes.
•
To cancel the AUTO SETUP procedure after it is started, press
RETURN.
8
Press ENTER to start the AUTO
SETUP procedure and then leave
the room within 10 seconds.
CINEMA DSP
SURROUND
STEREO
ENTER
TOP MENU
MENU
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is complete, the "SHOW
RESULT" screen appears on the TV.
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
If "ENVIRONMENT CHECK (FAILED)" is displayed, see "Error
massages for AUTO SETUP" of "Owner's Manual" (on the
supplied CD-ROM) and then run the procedure again.
y
•
The result may differ depending on the environment.
•
If any error occurs, the corresponding error message appears on the
screen. In this case, see "Error massages for AUTO SETUP" of "Owner'
s Manual" (on the supplied CD-ROM).
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the unit.
The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
AUTO SETUP START
Will begin in 10sec
Please leave the room
*--------
[RETURN]:Cancel
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5Beam/Plus2
SUBWOOFER :YES
9
Press ENTER.
The following screen appears on the TV for 2 seconds and
then the menu screen disappears from the TV.
CINEMA DSP
SURROUND
STEREO
ENTER
TOP MENU
10
Disconnect the IntelliBeam
microphone.
Now the AUTO SETUP is complete. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
5
Checking digital
audio input
You can check the digital signals being input from the Blu-ray disc player through
the digital connection (HDMI, optical, coaxial) by using the supplied demonstration
DVD.
1
Press HDMI1-4 or AUX1/2 to
select the Blu-ray disc player
as the input source and start
playback of the demonstration
DVD.
2
Check whether the q DIGITAL
indicator lights up.
y
•
If the indicator does not light up, check the setting for digital audio output
on the player. For details, see "Using the supplied demonstration DVD"
(page 7 of "Safety and Accessory Information" (separate booklet)).
– –
AUTO SETUP COMPLETE
Please remove the MIC from
the unit and the listening
position.
MENU
INPUT
VOLUME
INTELLIBEAM MIC
INTELLIBEAM MIC
TV
AUX 1
AUX 2
HDMI 1
HDMI 2
HDMI 3
HDMI 4
iPod
RADIO
ENTER
DIGITAL
q