Directechs PKUCH2GX Manuale di installazione - Pagina 2
Sfoglia online o scarica il pdf Manuale di installazione per Radio marina Directechs PKUCH2GX. Directechs PKUCH2GX 3. Chrysler 1st & 2nd generation sentry key override with 2nd start activation output
Stampa la paginaPKUCH2GX
Description:
Chrysler 1st & 2nd Generation Sentry Key Override with 2nd Start Activation Output (
Functions:
Transponder Bypass Kit for 1st & 2nd generation encrypted Chrysler Sentry key immobilizer systems. This transponder
bypass kit will override all Chrysler, Dodge & Jeep vehicles equipped with the 1st & 2nd generation type of Sentry
transponder key. PKUCH2GX designed with MUX (2nd starter & accessory wire) activation output
Starter & 2nd accessory wire during start up.
For Durango 2004 built before 17/05/04:
PKU-CH2GX Transponder Override module is compatible with 2004 Dodge Durango. A manufactures issue exists with Durango vehicles built before May 17 2004 and
is covered under warranty. The WCM module is defective and does not permit ANY additional RFID codes to be added to the vehicle. This includes new ignition keys
(Sentry keys). Instead of recalling all Durango's for this module swap Chrysler is only changing the WCM when a Durango owner requests a new transponder key.
The WCM does not affect any other functions so is not a mandatory swap unless a new RFID is added. The PKU-CH2GX supplies the vehicles with a RFID and thus
must be programmed like a new key. The WCM will allow additional RFID codes to be programmed if the Mfg date is after May 17th otherwise the original WCM must
be changed under warranty in order to program the PKU-CH2GX to the Durango. The WCM replacement part number is 56038675AS.
For key with integrated remote, see optional programming instructions.
Programming mode for coded key Chrysler with integrated remote
You will need 2 valid keys. Proceed as follows:
1- Insert first key and turn to the IGN "ON" position: "THEFT" light will turn ON, then go "OFF". Remove the first key.
2- Within 5 seconds, insert second key: turn and hold in IGN "ON" position. After approx. 10 seconds, the door chime
will sound** once to indicate vehicle is in programming mode.
YOU NOW HAVE 60 SECONDS TO PROCEED WITH THE NEXT STEP.
4- Remove cover and PC board from factory remote (See illustration A)
5- Position bypass module on the side of the empty factory remote (See illustration B)
6- Keep the bypass module on the side of the empty factory remote, insert key and turn it to ON position (Ignition) f
period of 10 sec, you will hear a chime, the light will turn on for 3 sec. Keep the key at this position for 5 sec. Then,
turn the key off and remove the key.
7- Close remote and re-install screw.
IMPORTANT NOTE:
Once the PK (Transponder Bypass) portion has been programmed to a vehicle, it cannot be used on any other
Chrysler vehicle. (This a Chrysler Sentry Key feature from factory.)
Illustration A
This Interface kit / Data Bus In erface part has been t sted on th listed vehicles. Other v hicles w ll b added to th se e t vehicle list upon c mpletion of compa ibility testi g.
t
V
isit ebsite for latest vehicle a plication guide.
w
p
held liable for any cons quential damages sustained in connection with the part(s) installation. The manufacturer and it's distri utors will not, nor will they a thoriz an
e
representative or any other indiv dual to assume obligation or li bility in relat on to the interface kit / data bus inte face part(s) other than its r placement.
cir umstance shall the manufacture and di tributors of this product e liab e for consequen ial damages ustained in connection with th s product and neither assumes nor
c
s
auth rizes any repr sentative or other per on to assume for it any obligation or liability other than the re lacement of this product only.
o
e
The module is now programmed.
e
e
DISCLAIMER
: Under no circumstances shall the manufacturer or the distributors of the ypass kit / da a bus int rface part(s) be
i
a
r
s
s
Bypass Method: RF override through induction using loop antenna.
**As a reference: door should be left open during programming
Illustration B
e
i
e
i
b
l
t
p
No Key Required)
e
l c
o
b
b
r
s
i
Installation
Manual (2\3 Pages)
which initiates the 2nd
or a
.
t
n
t
e
u
e
y
e
N.B.:Under no