ALDI 55945 Manuale d'uso - Pagina 10

Sfoglia online o scarica il pdf Manuale d'uso per Trapano ALDI 55945. ALDI 55945 16. 24v lithium-ion cordless drill with hammer action & 2 x batteries

Stampa la pagina

Using the Drill / Driver

Rechargeable Battery Display

1. The rechargeable battery display (7) indicates the level of power left in the

battery (9). To check the power of the battery, press on the trigger switch

(8) to activate the drill, and the lights will be activated.

2. When all 3 lights are lit up, the battery is fully charged. When 2 lights are

lit up, the battery is at approx 50-60%. When only 1 light is lit up, there is

approx 20% power left in the battery (9).

2 Speed gearbox

The 2 Speed Gearbox allows you to select a gear

with the optimum speed and torque to suit the

application.

NOTE: When changing the two speed high /

low gear selector (4), ensure the drill/driver is not

operating.

1. To select the LOW gear (low speed, high torque

setting), push the gear selector (4) backward,

towards the back of the drill/driver. The number

"1" will be displayed (Fig F).

2. To select the HIGH gear (high speed, low torque

setting), push the gear selector (4) forward, towards the chuck.

The number "2" will be displayed (Fig F).

Using the drill/driver

Trigger switch

1. Use the forward/reverse switch (6) to select the

direction of rotation (Fig G), then pull the trigger

(8) (Fig H). This trigger switch is an electronic

variable speed control which enables the user

to vary the speed continuously.

The speed varies according to how far the

trigger switch is depressed.

The further it is depressed the faster the chuck

will rotate and the lighter it is depressed, the

slower it will rotate.

e-mail: [email protected]

MODEL: №. 2024001 • 02/2017 • 55945

24v Lithium-ion Cordless Drill with Hammer Action

The picture here shows the gear

selector forward so the drill/driver

is in High speed, with the number

2 displayed.

AFTER SALES SUPPORT

1800 909 909

(toll free)

24v Lithium-ion Cordless Drill with Hammer Action

2. To stop the drill/driver, release the trigger

switch (8).

Note. The variable speed control fitted to this

drill/driver is NOT intended to be used for long

periods of time during the operation of the task

being performed. Use the variable speed to start

drill/driving and screwing tasks, and then fully

depress the trigger once the task has started.

CAUTION. Extended use of the variable speed

under load will overload and then permanently damage the speed control.

Forward/reverse switch

NOTE: You can only change the direction of rotation of the drill/driver using

the forward/reverse switch (6) when the trigger (8) is NOT depressed.

This switch will allow you to change the direction of the motor while the

trigger switch is not depressed.

1. To put in reverse mode, push in the forward/reverse switch on the side of

the drill where the arrow on the switch is pointing to the rear end of the

drill. The chuck will rotate in an anti-clockwise direction.

2. To put in forward mode, push in the forward/reverse switch on the side of

the drill where the arrow on the switch is pointing to the front end of the

drill. The chuck will rotate in an clockwise direction.

Drill/driving uses the forward mode. The reverse mode is intended for the

removal of screws and assisting to remove jammed drill/driver bits.

Adjustable torque

This drill/driver is equipped with 25 torque settings plus 1 x drill setting,

1 x screw setting and 1 x hammer setting.

The torque settings are controlled and adjusted by the torque setting collar

(2), but only affects the output when the screw function (14) is selected.

The screwdriving function (14), the drill function (15) and the hammer

function (13) are all selected using the second collar, the function selection

collar (3).

AFTER SALES SUPPORT

1800 909 909

(toll free)

Using the Drill / Driver

e-mail: [email protected]

MODEL: №.2024001 • 02/2017 • 55945