Clarke ZX 500 Istruzioni per il funzionamento e la manutenzione - Pagina 5
Sfoglia online o scarica il pdf Istruzioni per il funzionamento e la manutenzione per Compressore d'aria Clarke ZX 500. Clarke ZX 500 6.
Stampa la pagina
MONTHLY
Start the compressor, and pressurise the system. Inspect all joints for leaks using soapy water,
and rectify as necessary.
EVERY 250 HOURS OR 6 MONTHS
(Whichever occurs first)
Change the compressor oil. Drain oil by removing the breather and turning the compressor
on to its end. Support it in this position and leave for a period to ensure all oil is drained.
Caution
Do not attempt any repairs or adjustments if you are uncertain as how it should be
done. If you have any queries, please contact your nearest CLARKE dealer, or
otherwise telephone CLARKE International, Service Department, on: 020 8988 7400).
Shutting Down The Compressor
1.
Push the STOP/START switch down to the OFF position.
NEVER USE THE MAINS SWITCH TO STOP THE MOTOR.
2.
Depress the tool's trigger to release air from the hose and compressor before
disconnecting from the machine.
3.
Switch off at the mains and remove plug.
Fault Finding
With considerate use, your CLARKE Air Compressor should provide you with long and
trouble free service. Routine checks should be made on both the electrical supply as well
as the compressed air lines and connections. If any fault appears, the reason for which is
not immediately obvious, please contact your local CLARKE Dealer.
PROBABLE CAUSE
PROBLEM
Bad connections.
The compressor
stops and will not
start again.
Thermal Overload has
intervened.
Motor windings burnt out.
The compressor
Compressor head gasket
does not reach the
blown or valve broken.
set pressure and
Broken piston
overheats easily.
Low Pressure
Air Leak - safety Valve
Restricted air filter
Defective Check Valve
REMEDY
Check electrical connections.
Clean and tighten as necessary.
Switch off and wait at least 5
minutes before trying to restart
Contact your local dealer for a
replacement motor.
Contact your CLARKE dealer.
Replace Piston (contact your
CLARKE dealer)
Blip safety valve by pulling the pull ring. If
condition persists See your Clarke dealer
Clean air filter, or replace
See your Clarke dealer
- 8 -
Electrical Connections
This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for
connection to a standard, domestic electrical supply. Should the plug need changing at
any time, ensure that a plug of identical specification is used.
WARNING! THIS APPLIANCE MUST BE EARTHED
Should the plug need changing at any time, ensure that a plug of identical
specification is used. IMPORTANT: The wires in the mains lead should be wired up in
accordance with the following colour code:
Green & Yellow ..................... Earth
Blue ........................................ Neutral
Brown ..................................... Live
•
Green & Yellow
Connect the
" E "or marked with the symbol "
•
Connect the BLUE coloured cord to the plug terminal marked a letter "N"
•
Connect the BROWN coloured cord to the plug terminal marked a letter "L"
If this appliance is fitted with a plug which is
moulded on to the electric cable (i.e. non-
rewireable) please note:
1. The plug must be thrown away if it is cut from
the electric cable. There is a danger of
electric shock if it is subsequently inserted
into a socket outlet.
2. Never use the plug without the fuse cover
fitted.
3. Should you wish to replace a detachable
fuse carrier, ensure that the correct replacement is used (as indicated by marking or
colour code).
4. Replacement fuse covers can be obtained from most DIY or electrical stores.
FUSE RATING
The fuse in the plug must be replaced with one of the same rating (13amps) and this
replacement must be ASTA approved to BS1362.
We recommend that this machine is connected to the mains supply via a Residual Current
Device (RCD)
If in doubt, consult a qualified electrician. Do not attempt any electrical repairs yourself.
CABLE EXTENSION.
Always use an approved cable extension suitable for the power rating of this tool (see
specifications), the conductor size should also be at least the same size as that on the
machine, or larger. When using a cable reel, always unwind the cable completely.
coloured cord to the plug terminal marked a letter
"
- 5 -