Directed Xpresskit DBALL2 Manuale di installazione - Pagina 11

Sfoglia online o scarica il pdf Manuale di installazione per Per serrature Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 15. Ford5 remote start ready (rsr) installation
Anche per Directed Xpresskit DBALL2: Manuale di installazione (12 pagine), Manuale di installazione (19 pagine), Manuale di installazione (18 pagine), Manuale (14 pagine), Manuale di installazione (13 pagine), Manuale di installazione (14 pagine), Manuale di installazione (19 pagine), Manuale di installazione (16 pagine), Manuale di installazione (20 pagine), Manuale di installazione e di consultazione rapida (16 pagine), Manuale di installazione (18 pagine), Manuale di installazione (16 pagine), Manuale di installazione (18 pagine), Manuale di installazione (16 pagine), Manuale (19 pagine)

Stampa la pagina
Directed Xpresskit DBALL2 Manuale di installazione
Platform: DBALL2
Firmware:
NISS06
Remote Start Ready
LED Diagnostics & Troubleshooting
LED
Description
Module Programming
Off
Module has no power.
Waiting to begin the programming sequence.
Solid red
Initialization failed.
Flashes red
& green
Solid orange
Transponder functions were skipped.
Flashes
All required CAN networks has been detected.
green
Flashes
1 of 2 CAN networks has been detected.
orange
Flashes
Key2GO initiated.
orange
slowly
Solid green
Module was successfully programmed with all functions. Normal operation
x 3 secs
Module was successfully programmed without
Solid orange
x 3 secs
transponder functions.
Module Programming - Error Codes
Flashes red
CAN2 not detected.
x 1
Flashes red
J1850 not detected.
x 1
Flashes red
CAN1 not detected.
x 2
Flashes red
Bypass data not detected.
x 3
Flashes red
Bypass processing error.
x 4
Flashes red
ISO 1 not detected.
x 5
Flashes red
ISO 2 not detected.
x 6
Flashes red
MUX not detected.
x 7
(RSR)
Installation
Troubleshooting
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Ensure the correct programming procedure is being
followed.
Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
Normal operation.
Normal operation
Please follow the steps indicated in "Module
programming" to complete the Key2GO programming.
Normal operation.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Rev.: 20
1707
12
Page 11
© 2017 Directed. All rights reserved.