ARMORDILLO RS Running Boards Manuale di istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Automobile Accessories ARMORDILLO RS Running Boards. ARMORDILLO RS Running Boards 6. 2009-2018 doge ram 1500 - crew cab, 2010-2018 ram 2500/3500 - crew cab, 2018-2022 ram 1500 classic - crew cab, excl. chassis cab diesel models
Anche per ARMORDILLO RS Running Boards: Manuale (8 pagine)
Stampa la paginaHex Bolt as a handle and insert the Bolt-Nut Plate into the oval hole, (Figure 4). Feed the threaded
bolt on the Bolt-Nut Plate through one of the hex shaped factory holes.
b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,
(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt-Nut Plate from falling into the
body panel and to aid in Bracket installation.
4. Select (1) Passenger/Right Support Bracket, for use on the Driver/Left Front mounting location, (Figure
6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock
Washer and (1) 8mm Hex Nut, (Figure 6).
c. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 3a. Rotate the Bolt on the Bolt-
Nut Plate until the threaded nut lines up with the remaining hole in the Bracket and hex hole in the
body panel, (Figure 5). Attach the Bracket to the threaded nut with (1) 8mm x 30mm Hex Bolt, (1)
8mm Lock Washer and (1) 8mm Flat Washer, (Figure 6). Do not tighten hardware at this time.
Models with factory threaded inserts, (see Figure 7):
a. Select (1) Passenger/Right Support Bracket, for use on the Driver/Left Front mounting location.
Attach the Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers
and (2) 8mm Flat Washers, (Figure 8). Leave hardware loose.
5. Select (1) Passenger/Right Support Bracket, (for use on the Driver/Left Front mounting location). Attach
the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (1)
8mm Nylon Lock Nut, (Figure 9). Do not tighten hardware at this time.
6. Next, attach the Support Bracket to the back of the pinch weld with (2) 6mm Button Head Bolts, (4)
6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Figure 10). Do not tighten hardware at this time.
IMPORTANT: Most 2009-12 models are not equipped with factory holes and will require drilling through
the pinch weld to attach the Bracket. Do not drill through pinch weld at this time, (see Step 10).
7. Move to the center mounting location, (Figure 11). Repeat Steps 2—6 to attach (1) Driver/Left
Mounting Bracket and (1) Driver/Left Support Bracket to the center location.
8. Move to the rear mounting location, (Figure 12). Repeat Steps 2—6 to attach (1) Driver/Left Mounting
Bracket and (1) Driver/Left Support Bracket to the rear location
9. Carefully unwrap and select the Driver/Left Running Board. Attach the Running Board mounting tabs to
the front face of the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6)
10mm Nylon Lock Nuts, (Figure 13). Do not tighten hardware at this time.
10. Properly level and adjust the Running Boards and fully tighten all hardware.
2009-12 models requiring drilling to attach Brackets to pinch weld:
a. Level the Running Board to the vehicle. Make sure all (3) Brackets are tight against the bottom of
the body panel and tighten all mounting hardware.
b. Mark the location of the slots onto the pinch weld.
c. Temporarily remove the Running Board and the (3) Mounting Brackets. Drill (2) 1/4" holes through
the pinch weld for each Bracket. IMPORTANT: Do not drill too close to the bottom edge of the pinch
weld. Drill the holes in the center of the marked slots.
d. Repeat Step 4 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully
tighten all hardware.
11. Repeat Steps 2—10 to attach the Passenger/Right Running Board.
12. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap
may be used to clean the Running Boards.
2009-2018 Doge Ram 1500 - Crew Cab
2010-2018 Ram 2500/3500 - Crew Cab
2018-2022 Ram 1500 Classic - Crew Cab
Excl. Chassis Cab Diesel models)
(
Page 3 of 6
RS Running Boards
4/30/20 (AL)