Arnica Puf Puf Plus Manuale di istruzioni - Pagina 11
Sfoglia online o scarica il pdf Manuale di istruzioni per Ferro Arnica Puf Puf Plus. Arnica Puf Puf Plus 12.
Anche per Arnica Puf Puf Plus: Manuale di istruzioni (12 pagine)
Stampa la paginaSetting the temperature:
• It is normal that a little fume comes out in your first use of the device. This state will stop after a little while.
• Before starting the ironing operation; always look at the product maintenance label on the things (shirt, pants etc) you will iron. What temperature to iron is mentioned there.
• If product maintenance label is not available and you know the type of the fabric, you may make benefit of the following table while choosing the temperature of your iron.
PRODUCT MAINTENANCE LABEL FABRIC TYPE
• Before starting to iron, classify the things you will iron (woolens, cotton velvets etc). Then start ironing operation from the group that requires the lowest temperature.
• If the fabric consists of the raw materials requiring different ironing degrees of temperature; ironing degree of temperature must be set according to the raw material requiring lower
degree (for example; if the fabric consists of polyester and cotton, it must be ironed at the setting of polyester requiring low ironing temperature).
• If you don't know what kind of fabric the dress is made of, determine the correct ironing temperature by ironing a part of the dress that is not seen when you wear.
• In order to avoid the formation of bright stains on silky, woolen and synthetic materials, iron the fabric back. In order to avoid the formation of stains, abstain from using the spraying
property.
• The device must be plugged into an earthed socket.
• Place the iron on its heel and ensure the required iron temperature by turning the temperature control button to its appropriate position.
• When the temperature light is off, wait for a while before starting to iron. The temperature light will be on and off time to time during ironing.
Steam Ironing:
1. Before starting steam ironing, be sure whether there is sufficient water in the water tank.
2. Set the temperature control button at its recommended position.
3. Set the steam control button at the appropriate steam position.
• For less steam (temperature settings •• /
• For much steam (temperature settings ••• /
Note: When the determined temperature is reached, the iron will start to omit steam.
Steamless Ironing:
1. Set the steam control button at 0 position.
2. Set the temperature control button at its recommended position.
Spraying Function;
In order to remove the creases, you may use spraying property at all temperatures.
1. Be sure that there is sufficient water in water tank.
2. Press several times on the spray button to moisten the fabric to be ironed.
Shock Steam:
A strong steam spraying helps to remove the creases. Steam spraying function only operates at the temperatures between **-MAX.
1. Press on the shock steam button and release.
Vertical Steam:
1. Shock steam function may also be used when you hold the iron at a vertical position. This processing is used to remove the creases found on the dresses on the hanger, curtains etc...
WARNING: Never direct the steam towards people and animals.
VALID FOR ANTIDRIP MODELS
NOTE: The property of stopping water dripping is available in this iron. The fact that the water enters into the soleplate without reaching a certain temperature has been blocked by
means of a valve. When the iron reaches the required temperature, the valve is automatically opened and the iron starts to generate steam. And when the temperature falls down, the
valve is closed.
E.CLEANING AND MAINTENANCE
Before starting to clean your iron,
• Switch off your iron.
• Unplug your iron.
• Let it cool down well.
WARNING: Never immerse your iron in liquids such as water to clean it.
De-scaling:
1. Remove the calcification developed in your iron every two weeks. If the water in your residing region is very hard (for example, if particles fall from the soleplate during ironing),
de-scaling process must be done more frequently.
2. Set the steam control button at 0 position.
3. Fill water in the water tank at maximum level. Never put vinegar or other de-scaling chemical matters into the water tank.
4. Plug the iron.
5. Set the temperature button at MAX setting.
6. When the temperature light goes out, unplug the iron.
7. Hold the iron over the washbasin and set the steam control button at de-scaling position. Steam control button will move out slightly by springing.
8. Pull the steam control button out.
9. Hold the iron over the washbasin and rock it. Super heated water and steam will flow down through the holes in the soleplate together with de-scale and other residues (if any).
10. Put some vinegar into a glass and let the nozzle of steam control button sit in it for a time.
11. Don't bend the needle of the steam control button by any means and don't damage.
12. Re-mount the steam control button by placing the nozzle of the needle in just the middle of the hole and putting the small rim at the edge of the needle into the housing. While setting
the steam control button at
13. If there is still residue in the iron, repeat the de-scaling process.
After De-scaling Process;
1. Plug the iron and ensure that the iron gets warmer to make the soleplate dry.
2. When the temperature light goes out, unplug the iron.
3. In order to clean the water stains that might accumulate over the soleplate, move the iron slightly on an old rag.
Storing:
1. Set the steam control button at 0 position, unplug the iron and let it cool down.
2. Clean the soleplate of your iron with a soft cloth.
3. Store on the surfaces with soft base. Avoid contacting metal objects.
4. In order to clean your iron, don't use cleaning fibers, vinegar or other chemical matters by any means.
5. Rinse the water tank by water frequently and empty after cleaning.
6. Wind the electric cable around the cable spinning section.
7. Store the iron on its heel (vertically), on a dry and safe surface.
TEMPERATURE SETTING
Synthetic
* Low temperature
Silk-wool
** Middle temperature
Cotton-linen
*** High temperature
Never iron
)
)
position, press towards inside at the same time and set at 0 position.
11