Cub Elecparts TIRE INSIGHT Manuale di installazione rapida

Sfoglia online o scarica il pdf Manuale di installazione rapida per Strumenti di misura Cub Elecparts TIRE INSIGHT. Cub Elecparts TIRE INSIGHT 2. 4-wheel battery tpms system

Stampa la pagina

4-wheel Battery TPMS System

VS-63W018 Contents

Warning

FCC Regulations

Product Warning

System Installation

Important Safety Guide

1.Product Parts List

2.Sensor Installation

2.1 Installation Location

2.2 Sensor Assembly Process

3.Installation of Tire Pressure Monitoring Receiver

FCC Regulations

This tire pressure monitoring system has complied with Article 15 of the FCC regulatory

requirements of the USA, but it is still needed to pay attention to the following two items:

(1) Other harmful interferences may affect the system's normal operation.

(2) Abnormal operation may cause the system to fail.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. End users must follow the specific operating instructions for satisfying RF

exposure compliance. This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

Note: The product will not be guaranteed if user change or modify the hardware and

system design.

Product Warning

1.Do not operate a TPMS receiver while driving. The company is exempt from all

consequences because of driver's careless and improper operation.

2.The system adopts the wireless transmissi of signals. In some special circumstances,

interference or erroneous methods of operation or installation method errors may

cause weaker signal or its inability to receive signals. If the insulation adhesive sticker

of the windshield contains metal material, it will be likely to affect reception conditions.

If the tire pressure and temperature readings on the TPMS receiver are displayed as

---, this condition represents the receiver cannot receive signals　emitted by the

sensors. Drive the vehicle away from the current location (nearby there may be signal

interference) or drive the vehicle to a tire shop to check, or return the TPMS receiver to

distributor for repair. If the battery status of the TPMS sensors inside the tire is low

(because abnormal conditions continue to occur, the battery may make the TPMS

sensors continuously emit signals to warn the driver, so that battery life is shorter than

the normal life), please go as soon as possible to the specified service stations to

confirm whether the TPMS Sensors need to be replaced.

3.Please change the Receiver's dry battery or sensor while the Receiver's dry battery

power is low or Sensor Low battery warning is alarm, or it may cause the TPMS thus

cannot be operated and alarm　normally. You will take all risks and responsibilities for

this!

4.Temporary resealing or re-inflation products containing internal sealants or propellants

in any tire assembly may adversely affect the operation of the sensor/transmitter. The

product manufacturer does not assume any liability as a result of these.

System Installation

The wireless TPMS needs to be installed by qualified personnel in accordance with

installation manual to enjoy related warranty. If improper assemble or disassemble process

damages the sensor, it will not be covered by warranty.

Reminder: annual periodic inspection for the "sensor valve" is proposed, which should be

replaced immediately if damaged, in order to avoid air leakage.

Important Safety Guide

System Warning

When the system displays a warning light and warning "beeps", you should immediately

slow down, stop in a safe location and check the tire condition, and immediately drive to

the nearest qualified tire maintenance garage to repair and make related in-depth

examination.

1.Product Parts List

Part Name

Sensor

Valve package (valve and screw)

Tire pressure monitoring receiver

AA battery

Quick installation guide

Product warranty card

Velcro

Quick Installation Guide

3.1 Buttons Function Introduction

3.2 Warning Light Symbol

3.3 Recommend the Receiver Mounting Position

4.Setting Items

4.1 Tire Pressure Unit Setting

4.2 Volume Setting

4.3 Tire Pressure Standard and Temperature Warning

Value Setting

4.4 ID Learn Setting

4.5 Tire Position Rotation Setting

Warning

Q'ty

2.Sensor Installation

2.1 Installation Location

Please follow the label on the sensor, install the sensor into the rims accordingly, it could

skip the "ID Learning" steps for each sensor!

2.2 Sensor Assembly Process

(Fig 1) Loosen the tire. Fix both sides of the tire and press, and make it bulge.

(Fig 2) Remove the tire. The valve faces the mounting arm in the one o'clock direction,

remove the tire.

(Fig 3) Remove the sensor. Loosen the fixing screw, allow the sensor separate from the

valve, and release the nut to take it apart from the valve.

(Fig 4) Install the sensor and valve. Insert the valve through the rim hole, fix the screw to

secure the valve and sensor by 2 Nm in torque, attach the sensor body to the inner

surface of the rim by adjusting the angle of the sensor body.

(Fig 5/6) Install valve to the rim hole. Guide the washer into the valve, and fix the nut by 4

Nm in torque, then tighten the cap.

Note: Mount the tire. Grip the rim edge, and the valve is opposite to the mounting arm, avoid

hitting the sensor during arm operation.

Fig 1

Fig 2

Outside of the rim

Fig 3

Fig 4

Fig 5

3.Installation of Tire Pressure Monitoring Receiver

3.1 Buttons Function Introduction

Function key

Normal mode

Backlighting and enter the function

setting mode (hold for 3 seconds)

Mute the warning audio

Switch to tire temperature mode for

10 seconds

Set the backlight to be always on/off

psi

Bar

SETTINGS

LEARNING

3.2 Warning Light Symbol

No.

Light Symbol

Abnormal Light Message

Alarm for excessive high/low tire pressure

Alarm for excessive high tire temperature

Warning for low battery in TPMS sensor,

need to replace new sensor

Warning for low battery in receiver,

need to replace new battery

1.Screw

2.Sensor

3.Rubber washer

4.Valve core

5.Washer

6.Washer

7.Nut

Inside of the rim

8.Valve cap

Fig 6

Setting mode

Leave function setting mode

Save the setting

Up and down selection/

value adjustment

Unit setting or right button