ARO 650125-M Manuale dell'operatore - Pagina 2
Sfoglia online o scarica il pdf Manuale dell'operatore per Pompa dell'acqua ARO 650125-M. ARO 650125-M 4.
Item Description
(size)
1 Bolt
2 Upper Cap
3 Track Gasket
4 Sleeve
5 "O" Ring
(1/16" x 11/16" OD)
6 "O" Ring
(1/8" x 3/4" OD)
7 Spool
8 "U" Cup
(1/8" x 3/4" OD)
9 "O" Ring
(0.106" x 0.587" OD)
10 Muffler Housing
11 Cylinder
12 Retaining Ring
13 "U" Cup
(3/16" x 2" OD)
14 Piston
15 Lower Cap
16 "O" Ring
(1/8" x 1-3/8" OD)
17 Bushing
18 Packing
(1/4" x 1-5/8" OD)
19 "O" Ring
(3/32" x 1" OD)
20 Piston Rod
21 Groove Pin
(3/16" OD x 1-1/8" long)
22 Spring
23 Ball
(3/4" dia.)
24 Inner Check
Model 650125-M two-ball double acting pumps are intended to be
used primarily for oil transfer and delivery systems. It is best to use
this pump with low - medium viscosity fluids. It uses carbon steel
and other materials which make it compatible with most petroleum
based lubrication products. The two-ball design provides better
priming of th lower foot valve. Double acting pumps will deliver
material on both the up and down stroke.
NOTE: If this pump was purchased separately (not part of a system),
consult your sales representative for compatible dispensing acces-
sories which will best match the application. All accessories must be
able to withstand the maximum pressure developed by the pump.
OPERATING AND SAFETY PRECAUTIONS
READ THE GENERAL INFORMATION MANUAL
WARNING
INCLUDED FOR ADDITIONAL OPERATING AND SAFETY
PRECAUTIONS AND OTHER IMPORTANT INFORMATION.
STATIC SPARK.
WARNING
Can cause explosion resulting in severe injury or death. Ground
the pump and pumping system.
EXCESSIVE INLET PRESSURE.
WARNING
Can cause explosion resulting in severe injury or death. Do not
exceed maximum operating pressure of 450 psig (31.0 bar) at
150 psig (10.3 bar) inlet air pressure. Do not run pump without
using a regulator to limit air supply pressure to the pump.
Page 2 of 4
PARTS LIST / 650125-M
Qty
Part No.
Item Description
25 "O" Ring
(4)
94333
26 Base
(1)
96592
27 Nut
(2)
94311
28 Copper Gasket
(2)
94316
29 Tube
(4)
Y325-15
30 "O" Ring
(4)
Y325-206
31 Ball
(1)
94310
32 Ball Stop Pin
33 Foot Valve
(2)
Y240-7
34 "O" Ring
(2)
15066-PM
35 "O" Ring
(1)
96595
36 Adapter
(1)
94249
37 Foam Liner
(1)
94406
38 Ground Screw
(2)
Y240-23
39 Bung Assembly
(1)
94780
48 Washer
50 Sensor
(1)
94308
51 Sensor Adapter
(1)
Y325-216
52 "O" Ring
(1)
94332
53 Magnet
(1)
94337
54 Spool
(1)
Y325-117
(1)
94779
(1)
94338
INCLUDED ITEMS BUT NOT ASSEMBLED TO THE PUMP DURING SHIPMENT
(1)
94705
TO BE PLACED IN CARTON PER ARO SPEC #S-620
(1)
Y16-224
(1)
94279
GENERAL DESCRIPTION
INLET PRESSURE TO PUMP MOTOR
Pump ratio is an expression of the relationship between the pump motor area and
the lower pump end area. EXAMPLE: When 150 psig (10.3 bar) inlet pressure is
supplied to the motor of a 3:1 ratio pump it will develop a maximum of 450 psig
(31.0 bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate
will increase as the motor cycle rate increases to keep up with the demand.
WARNING
Can cause equipment failure resulting in severe injury or prop-
erty damage. Do not exceed the maximum material pressure of
any component in the system.
NOTICE: Thermal expansion can occur when the fluid in the
material lines is exposed to elevated temperatures.
Example: Material lines located in a non-insulated roof area can
warm due to sunlight. Install a pressure relief valve in the pumping
system.
Replacement warning label (pn 94520) is available upon request.
(size)
(3/16" x 1-7/16" OD)
(3/32" x 1-9/16" OD)
(1" dia.)
(0.187" dia. x 1.430" long)
(1/16" x 7/16" OD)
(1/16" x 3/4" OD)
(#10 - 32 x 1/4")
(0.4375" x 0.5625" OD)
(0 0.150)
Gadus S2 U1000 Grease Packet
Parts in Repair Kit
PUMP RATIO X
EXCESSIVE INLET PRESSURE.
Qty
Part No.
(1)
Y325-319
(1)
96253
(4)
93828
(1)
96031
(1)
94314-1
(1)
Y325-126
(1)
Y16-232
(1)
94339
(1)
94315
(1)
Y325-11
(1)
Y325-16
(1)
94447
(2)
94402
(1)
93005
(1)
67145-3-B
(1)
94515
(1)
95276
(1)
96593
(1)
Y325-13
(1)
95275
(1)
96594
(1)
94833
637224
MAXIMUM PUMP
=
FLUID PRESSURE
650125-M (en)