ARO 66605 series Manuale dell'operatore - Pagina 6

Sfoglia online o scarica il pdf Manuale dell'operatore per Pompa dell'acqua ARO 66605 series. ARO 66605 series 8. 1/2 inch diaphragm pump 1:1 ratio (non-metallic)

ARO 66605 series Manuale dell'operatore
(n) Indicates parts included in 637141 Air Section Repair Kit.
ITEM DESCRIPTION
(Size in Inches)
101 Motor Body
n102 O" Ring
(3/32" x 1" o.d.)
j103 Sleeve
j104 Snap Ring
(13/16")
111 Spool
118 Pilot Rod
n119 O" Ring
(1/8" x 3/4" o.d.)
j120 Spacer
n122 Snap Ring
(1/2")
124 Stud
(5/16" 18 x 1 17/32") shown pg. 5
129 Muffler Assembly
Exhaust Cover
129
l
(see note 2)
n130 Gasket
131 Bolt
(5/16" 18 x 1 1/4")
n132 Gasket
(see note 1)

DIAPHRAGM PUMP SERVICE

GENERAL SERVICE NOTES:
S
Inspect and replace old parts with new parts as necessary. Look for
deep scratches on metallic surfaces, and nicks or cuts in O" rings.
S
7/16" Wrench, 1/2" Wrench, 7/16" Socket, 1/2" Socket, Torque
Wrench (measuring inch pounds), O" ring Pick.

FLUID SECTION DISASSEMBLY

1. Remove (34) top manifold / (36) swivel assembly.
Note: Manifold options involve single piece manifolds (60 / 61) or three
piece swivel type manifolds with clamps.
2. Remove (41) ball cages, (22) balls, (19 and 20) ``O" rings and (21)
seats. Note: If cages are difficult to remove at this step, it may may
helpful to proceed through step 5 and remove them once they are
accessible from the inside of the fluid cap.
3. Remove (35) bottom manifolds / (36) swivel assembly.
4. Remove (19) O" rings, (21) seats and (22) balls.
5. Remove (15) fluid caps.
6. Remove (6) diaphragm nut, (8) [(7) Teflon Models only] dia
phragm(s) and (5) diaphragm washer from (1) diaphragm connect
ing rod.
7. Remove (1) connecting rod from air motor.
8. Carefully remove remaining (6) diaphragm nut, (8) [(7) Teflon Mod
els] diaphragm and (5) diaphragm washer from (1) connecting rod.
Do not mar surface of connecting rod.
9. Remove (2) O" ring from connecting rod.
10. Remove (37) clamps from top and bottom manifold / swivel assem
blies.
11. Remove (33) O" rings from (36) swivels.
V Smart Parts" keep these items on hand in addition to the Service Kits for fast repair and reduction of down time.
PAGE 6 OF 8
PARTS LIST / 66605X-X AIR MOTOR SECTION
AIR SECTION PARTS
QTY
PART NO.
[MTL]
(1)
93091
[P]
(2)
Y325 117
[B]
(1)
93087
[Bz]
(2)
37285
[C]
(1)
93085
[D]
(1)
93088
[C]
(4)
93075
[U]
(3)
115959
[Z]
(2)
77802
[C]
(8)
93249
[SS]
(1)
66972
[P]
93092
[PS]
(1)
93107
[SY]
(8)
93095
[SS]
(1)
93339 1
[B]
ITEM DESCRIPTION
(Size In Inches)
133 Washer
(9/32" i.d.)
134 Bolt
(1/4" 20 x 5")
135 Valve Block
136 Plug
n137 O" Ring
(3/32" x 1 1/2" o.d.)
n138 Packing, U" Cup
(1/8" x 1" o.d.)
n139 Packing, U" Cup
(1/8" x 1.427" o.d.)
n140 Valve Insert
n141 Valve Plate
142 Washer
143 Plate
201 Muffler
(see note 2)
n Keylube O" Ring Lubricant
10 Pack of Keylube
Note 1: Part No.93339 1 One Piece Gasket replaces the following parts (not shown) in
models manufactured prior to October 1988, Y325 10 (4), Y325 12, 93093, 93094,
Y325 8.
Note 2: The (129
) Exhaust Cover and (201) Muffler were standard until 9/92. They are
l
available separately for service or piped exhaust applications.
Note 3: A Major Valve Service Assembly is available separately which includes items: 111,
132, 135 141. Order part no 66362.
MATERIAL CODE
[B] = Nitrile
[D] = Acetal
[Bz] = Bronze
[P] = Polypropylene
[C] = Carbon Steel
[PS] = Polyester
[CK] = Ceramic
[SS] = Stainless Steel

FLUID SECTION REASSEMBLY

S
Reassemble In reverse order.
S
Lubricate (1) connecting rod and (2) O" ring with Key Lube or
equivalent O" ring lubricant.
S
Install (5) diaphragm washers with i.d. chamfer toward diaphragm.
S
When replacing Teflon diaphragms, install the 93465 Santoprene
diaphragm behind the Teflon diaphragm.
S
When installing (41) cage, ball guides must line up with notches in
(21) seat to prevent damage.
S
Before installing (35), (34) manifolds, (19) O" ring should be prop
erly seated on the o.d. of (41) ball cage.
S
Before tightening (39) nut on (38) carriage bolts on (36) swivels, at
tach the manifold / swivel assembly to the fluid caps. Rotate (36)
swivel to desired position and tighten each of the nuts approx. 8 9
turns, then finish tightening (29) nuts.
QTY
PART NO.
[MTL]
(4)
93096
[SS]
(4)
Y6 419 T
[SS]
(1)
93090
[P]
(1)
93086
[UH]
(1)
Y325 125
[B]
(1)
94395
[U]
(1)
93116
[B]
(1)
93276
[CK]
(1)
93275
[CK]
(2)
116038
[Z]
(2)
93089
[SS]
93110
[C]
93706 1
637175
[SY] = Syn Seal
[U] = Polyurethane
[UH] = UHMW PE
[Z] = Zinc
66605X X