Dish Network ViP 211 Series Manuale

Sfoglia online o scarica il pdf Manuale per Telecomando Dish Network ViP 211 Series. Dish Network ViP 211 Series 2. Quick facts; quick remote control programming & tips for installers
Anche per Dish Network ViP 211 Series: Manuale di personalizzazione (10 pagine), Manuale di riferimento rapido (2 pagine), Come iniziare (2 pagine), Istruzioni per la configurazione (2 pagine)

Stampa la pagina

Introduction

This document only provides

the steps to program various

remote features. For more

details on each feature,

refer to Chapter 8 - Remote

Controls of the Installation

Reference Handbook.

Highlights

• Discrete ON and OFF

commands for learning

remotes

• Limited Mode &

Easy Limited Mode

• Power Scan

• Recover Button

• Extended Remote

Addresses

The programming

instructions included on this

page are for the following

remote control versions:

3.0, 3.1, 3.2, 4.0, 5.0, 5.2,

5.3, 6.0, 6.2, 6.3, 8.0, 8.1,

10.1

Mode

Buttons

POWER

VOLUME

MUTE

UP & DOWN

ARROWS

Numbers

POUND (#)

STAR (*)

Quick Remote Control Programming

& Tips for Installers

Sending Discrete Power On and Off

For most newer DISH Network remote

controls.

1. Program remote for desired remote

address.

2. Hold the SAT mode button down until all

mode lights are backlit, then release.

3. Press POWER (not TV Power).

4. Press VOLUME UP for discrete power on,

or VOLUME DOWN for discrete power off.

5. Press any other button when done to end

this procedure.

Programming Limited Mode for TV

While the steps below show how to program

Limited Mode for a TV, you can also program

Limited Mode for a connected VCR using the

same procedure (use VCR mode instead of

TV mode).

1. Turn the TV on.

2. Press and hold the TV mode button until

all mode buttons light up.

3. Enter one of the three-digit codes for your

TV model from the remote control user's

guide table.

4. Press 1 to program Limited Mode.

5. Press POUND (#).

6. Confirm that only the remote POWER,

MUTE, and VOLUME buttons work with the

TV.

Easy Limited Mode Setup

Only available in remote control models

3.2, some 5.2, 5.3, some 6.2 and 6.3.

To remove Limited Mode for these remotes,

use the procedure below and press the PAGE

DOWN button instead. This procedure can be

done for TV mode, VCR mode, and TVs and

VCRs programmed into AUX mode.

After programming one of the mode buttons:

1. Press and hold that MODE button until all

four mode lights are lit, then release.

2. Press PAGE UP once.

3. Press POUND (#).

Contents subject to change without notice.

EchoStar Technologies Corporation

Page 1 of 2

Scanning for TV Code

("Power Scan")

Use the quick steps below to scan the remote

control's memory for the code that works the

TV. You can also scan for other devices

(VCRs, etc.) using the same procedure (use

the other device mode instead of TV mode).

1. Turn the TV on.

2. Press and hold the TV mode button until all

mode buttons light up.

3. Press POWER (not TV Power).

4. Press just UP ARROW (or just DOWN

ARROW, but not both) repeatedly until the

TV turns off – a new code is sent each time

you press the button.

5. Press POUND (#).

6. Turn the TV on and confirm the remote

operates it.

Recover Button for

Remote Control 2

You can also program RECOVER for a

connected VCR using the same procedure

(use VCR mode instead of TV mode).

1. Program Remote Control 2 to control your

TV.

2. Press and hold the TV mode button until all

mode buttons light up.

3. Press STAR (*)

4. Enter your TV2 Agile channel using 3 digits

(ex. 0-6-0 for Channel 60).

5. Press POUND (#)

Extended Remote Address (17–31)

To program a remote control to operate in

the extended range (17 to 31), complete the

following:

1. Open the receiver's System Information

screen using the front panel SYS INFO or

SYSTEM INFO button.

2. Hold the SAT mode button down until all

mode lights are backlit, then release.

3. Press POUND (#).

4. Press CHANNEL UP to enter the extended

address mode.

5. Choose an extended remote address (a

number from 17 to 31), then subtract 16

from that address. Enter the result.

6. Press POUND (#). If the address was

entered correctly, the SAT mode button

flashes three times.

7. Press RECORD. Make sure the extended

remote address you see on the System

Information screen is the same as what you

wanted in step 5 (17 to 31). If it isn't, the

remote cannot control the receiver.

Rev. 7/17/2006