Balmar Max Charge MC-612 Manuale di installazione e funzionamento - Pagina 9

Sfoglia online o scarica il pdf Manuale di installazione e funzionamento per Attrezzatura marina Balmar Max Charge MC-612. Balmar Max Charge MC-612 17. Multi-stage marine regulator
Anche per Balmar Max Charge MC-612: Manuale d'installazione e d'uso (12 pagine)

Stampa la pagina

1. Programming Modes

VII. Programming Modes

A. Basic Programming

The Max Charge features six selectable programs for commonly used battery types: standard flooded, deep

cycle flooded, gel, AGM, Optima spiral wound, halogen (voltage sensitive), as well as a default program that's

safe for most battery types. To select the program that best suits your battery type:

Turn the ignition switch to the ON position. If an oil pressure switch is used, it may be necessary to start the engine

to engage the regulator.

Once the regulator is activated and the numeric display is illuminated, activate the regulator's reed switch with the

supplied magnetic screwdriver. Continue to hold the magnetic tip of the screwdriver against the reed switch.

The display will indicate entry into the Basic

Programming mode with the code

tinue to hold the magnet to the reed switch, the regula-

tor will scroll through the battery program choices

shown in the chart at right.

Select the preset programming that best suits your bat-

tery type. When the program number matching your

battery type is indicated on the display, release the

switch by lifting the screwdriver off of the epoxy pot-

ting.

Should you miss the desired program setting, simply

re-activate and hold the switch as described on the pre-

vious page. Once the programming display begins to

scroll upward, release the switch and wait for the

"PRO"

code. When the

activate and hold the magnet to the switch. The display

will scroll in the opposite direction. Release the magnet

from the switch as soon as the display indi-

cates your intended battery program.

After the switch is released, the regulator dis-

play will indicate

ments are required, re-activate the switch as

previously described. If no additional adjust-

ments are made, the display will indicate

"SAu"

, at which point, the regulator will save

any changes to the programming and the reg-

ulator will restart.

Programming success can be monitored by

the watching the regulator's display after

restart. The short display should indicate

both program number and program code, as

described on the chart shown above.

Primary Program Settings

Mode

Start Delay (Seconds)

Ramp Up (Seconds)

Bulk Voltage (Max)

Bulk Time (Minimum)

Absorption Voltage

Absorption Time (Minimum)

Float Voltage

Float Time (Maximum)

High Voltage Alarm

Low Voltage Alarm

Max Battery Temperature

Max Alternator Temperature

Equalization (User Prog.)

"PRO"

. As you con-

"PRO"

code is illuminated, re-

"PRO"

. If further adjust-

PRG-1

PRG-2

Universal

Deep Cycle

Factory

Flooded

Program

Lead Acid

14.10

14.60

36 min.

13.90

14.40

36 min.

13.42

13.35

6 hr.

15.20

15.60

12.80

125F/52C

225F/107C

Yes

Mastering The Magnetic Reed Switch

'ACTIVATE-RELEASE' Refers to the activation and immediate deactiva-

tion of the switch by lowering the magnetic programming tool onto the

potting covering the reed switch, and immediately deactivating the switch

by removing the magnet from the epoxy. An LED dot between the second

and third digits on the display will indicate switch activation.

'ACTIVATE - HOLD - RELEASE' Typically used during programming,

this action requires holding the magnet to the switch until desired values

are shown on the display. Once the desired setting is reached, the magnet

is removed to deactivate the switch.

Note: Program function will alternately cycle up or down each time the

programming mode is activated. If you miss your desired program value,

release the switch, wait for the program mode display (eg., PRO), and re-

activate the switch. The direction of scroll will reverse. Any advanced pro-

gramming values will be retained within the regulator's memory until the

preset battery programming is reset.

PRG-3

PRG-4

Gel

Absorbed

Cell

Glass

Mat (AGM)

14.10

14.38

36 min.

13.90

14.18

36 min.

13.70

13.38

6 hr.

15.10

15.38

12.80

125F/52C

225F/107C

Yes

- 9 -

PRG-5

PRG-6

Optima

Standard

Spiral

Flooded

Wound

Lead Acid

14.60

14.40

36 min.

14.40

14.20

36 min.

13.40

6 hr.

15.60

15.40

12.80

125F/52C

225F/107C

Yes

PRG-7

Halogen

Voltage

Sensitive

14.00

36 min.

13.80

36 min.

13.50

6 hr.

15.00

12.80

125F/52C

225F/107C