Divine Tribe Ceramic Donut v3 Manuale di avvio rapido

Sfoglia online o scarica il pdf Manuale di avvio rapido per Sigarette elettroniche Divine Tribe Ceramic Donut v3. Divine Tribe Ceramic Donut v3 2.

Stampa la pagina

Divine Tribe v3 Ceramic Donut Atomizer Quick Start Guide

I want to use it now!

The atomizer works best with slow low draw hits. The donut takes a

couple seconds from cold to make vapor. Let off the fire button a few

seconds before you stop drawing. This helps keep the air holes open by

cooling any reclaim left in the atomizer. Load small

smaller ON the donut. Usually three to five 10

DO NOT load a lot of material at once

holes and into the base. DO NOT suck like a vacuum cleaner

just get splatter all over the cap. Now to setup your mod.

My mod has TCR mode – Stellar!

10mm donut TCR 240 20-24 watts

●

13mm donut TCR 475 30-35 watts

●

The above settings should allow the temperature on the screen to be

pretty close to the donut. F or the best results using TC, lock your

atomizer resistance at room temperature. Don't be afraid to tweak

these settings

higher TCR number will make the donut hotter than

–

the screen number and a lower TCR number will make the donut temp

lower than screen number.

My mod does TC but not TCR – Your best bet here is to use Ni

mode at 20-30 watts and a temperature limit somewhat lower than

the desired donut temperature. The ideal TCR number for the donut

is between 230 and 500 while the TCR number for Ni is around

600. A temperature between 280-360 should yield donut temps

between 360 and 420. Lock your atomizer resistance when cold.

My mod doesn't do temp control (TC)

needed to make enough heat to vaporize oil, but getting to 400F will

take 5 seconds or so. 20-30 watts heats the donut faster but you

MUST pulse the fire button to keep from blowing the donut. If you

are using a mod in wattage mod only, you probably already know this.

ineedhemp.com 2017

–

bb size or

–

15s hits on that bb.

–

it will just leak out the air

–

you'll

–

At least 12-16watts are

–

Advanced TC configuration

F or those with an eLeaf, Joyetech or Wismec mod and are pretty

handy with computers. A windows computer or windows virtual machine

is required to run the NFE toolbox which provides for configuring and

loading the ArcticF ox firmware (AFF) onto your mod. Also provided is

a device monitor for real time monitoring of the mod in use. AFF

allows a profile based configuration with intelligent switching of up to 8

atomizers. AFF also has support for PI regulator temperature control

and fully customizable screen output. All configurations can be

performed on the mod or via the NFE Toolbox interface. If all of this

still makes sense and sounds like a good idea

back.

The process of reflashing the firmware is very simple. Instructions can

be found at the

NFE Team F

orum. Make sure to use the required

version of the NFE Tools that go with the version of AFF you are

Plug your mod into the USB port on your computer and launch

Ntoolbox.exe. Use 'Firmware Updater" to reflash your mod. Choose the

AFF .bin file you downloaded.

Now you can configure profiles using "ArcticF ox Configuration". Start

with the same TCR configuration to the left. Then click the "setup"

button next to temp control and enable PI-Regulator. The percentage

value is when the PI-Regulator kicks in

enabled from start to finish while a number indicates percent of

desired temperature. I leave 0% and set P=950 and I=10. Testing

with an IR thermometer with emissivity set to 0.65 shows my donut

temp tracks within 10F of the displayed temperature. I create one

profile for 10mm donuts and one for 13mm donuts. I also like to

increase the puff cutoff time to 15 seconds on the "Advanced" tab.

(ArcticF ox Firmware)

proceed, you won't look

–

a zero value means it's

–

[email protected] | 707-709-8480