dji AIR 3 Manuale d'uso - Pagina 4
Sfoglia online o scarica il pdf Manuale d'uso per Caricabatterie dji AIR 3. dji AIR 3 5. Battery charging hub
Stampa la pagina
QB]
Warnings
1.
Place
the charging hub on a flat, stable surface
with
good
ventilation when
charging an external device
or accumulating power.
Make
sure tl"te device is
properly insulated to
prevent
fire hazards.
2.
DO NOT attempt
to
touch the metal terminals on
the
battery
ports. Clean
the
metal terminals
with
a
clean,
dry
cloth
if
there is
any
noticeable buildup.
3.
Make
sure to charge batteries
with
low battery
power in time. It Is recommended to store the
batteries in the charging
hub.
The
charging hub
automatically checks the battery power every
seven days.
When a battery
has
0%
power level, the
battery
with a
high power level
will
charge the low
power level
battery
until its
power
reaches
596
to
prevent over-discharging.
Introduction
The OJI™
Air
3 Battery Charging Hub is designed to
charge up to three Intelligent
Flight
Batteries.
After
the
lntelllgent Flight Batteries are installed, the charging
hub can supply power to extemal devices via the USB-C
port, such as remote controllers or mobile phones. The
charging hub can also use the power accumulation
function
to
transfer the remaining power of multiple
low-power batteries into the battery
with
the highest
remaining
power.
Usage
Charging
Intelligent Flight Battery
1. Insert the batteries into
the
charging hub until It
clicks Into place. (Figure
A
1)
2. Connect the charging hub to a power outlet using
a USB-C charger. The Intelligent Flight
Battery
with
the highest power level
will be
charged first, and
then the rest will be charged in sequence according
to their power levels. The status LED indicates the
battery level during charging. Refer to
the
Status LED
Descriptions for more information
about
the blinking
patterns
of the status LED.
3. The battery can
be
stored In the charging
hub
after
charging. Remove the battery from the charging
hub for use. (Figure
A2)
Using Charging Hub as a Power Bank
1. Insert an Intelligent Flight Battery Into the charging
hub. Connect an external device via the USB-C
port, such as a mobile
phone
or remote controller.
(Figure
B)
2.
Press the
function
button, and the status LED of the
charging hub turns solid green. The battery with the
lowest
power level will be discharged first, followed by
the remaining
batteries
to be discharged sequentially.
To stop charging
the
external
device,
disconnect the
external device from the charging hub.
•
If the remaining charge of a battery Is lower
than
796,
the
battery cannot charge the
external device.
Accumulating Power
1. Insert more than one battery into the charging hub,
and press and hold the function button until the status
LED rums green. The starus LED of the charging hub
pulses green, and the charge is
transferred
from the
battery
with
the lowest power level
to
the battery with
the highest power level.
·-
2. To stop accumulating
power,
press and hold
the
function button until the status LED turns yellow. After
stopping power accumulation, press the function
button to check the power level of the batteries.
•
Power accumulation stops automatically In the
following situations:
a. The
receiving
battery Is fully charged, or the
power of the output battery is lower than
5%.
b. A charger or external deVice is connected to
the charging hub or any battery is inserted
or withdrawn from the charging hub during
power accumulation.
c. Power accumulation Is Interrupted for more
than
1 S
minutes due to abnormal battery
temperature.
•
After
accumulating power, charge the battery
with
the lowest
power
level as soon as
possible
to
avoid discharge.
Status LED Descriptions
Solid yellow
Pulses green
~ ~ - - - - ~
Solid
green
The charging
hub
is idle
Charging the battery or
accumulating power
All batteries
fully
charged or
supplying power to external
devices
Blinks yellow
Temperature of the batteries Is
too low or too high (no further
_ _ _ _ _ _ _
operation needed)
Solid Red
Power supply error or battery
error (remove and reinsert the
batteries
or unplug and plug in
the
charger)
Specifications
Product
Model
Compatible
Power Adapter
Compatible
Battery Model
Dimensions
Weight
Operating
Temperature
Input (USB-Q
Output (USB-C)
CHX233-100
OJI
1
OOW USB-C Power Adapter,
OJI 65W Portable Charger, or
other USB PD chargers or PPS
chargers
BWX233-4241-14.76
170.6x48.3x112.8 mm
169g
5° to 40° C (41 • to 104° F)
5-20 V, Max. 5 A
SV=3A, 9V=SA, 12V=SA,
1
SV= SA, 20V=
4.1A
OJI 100W USB-C Power
Adapter.
Approx.
60
mlns
Charging Time
(Single
Battery)
OJI
65W Portable Charger: Approx.
80mins
3