Custom Dynamics MAGIC-STROBES-HD Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Accessori per moto Custom Dynamics MAGIC-STROBES-HD. Custom Dynamics MAGIC-STROBES-HD 2. Brake flasher
Anche per Custom Dynamics MAGIC-STROBES-HD: Istruzioni per l'installazione (2 pagine)

Stampa la pagina

Part Number: MAGIC-STROBES-HD

Package Contents:

- Magic Strobes™ Brake Flasher (1)

- Tie Wraps (5)

Fits: 1996-2010 Harley-Davidson® Softail® (Except

Convertible, Rocker and Breakout®), 1997-2011

Dyna®, 1997-2013 Touring (Except 2010-2013 Street

Glide®, Road Glide® Custom), 1999-2003 Sportster®,

2010-2013 TriGlide®, and 2011-2013 Road Glide®

Ultra

Installation

Secure motorcycle on level surface.

Remove seat or side panel, depending on model.

Disconnect negative [ - ] battery cable from the

battery.

Locate and unplug the lighting connector to the rear

fender.

Plug the Magic Strobes™ module, in-line, into the

rear lighting harness and into the bike's wiring har-

ness.

Re-connect the battery's negative battery

cable to the negative [ - ] of the battery.

Select desired pattern on the dial with power Off.

(See page 2 for Pattern Information)

Check operation.

To change pattern, turn bike OFF and change dial

to desired pattern.

10. Locate a secure place for the Magic Strobes™ unit

that will not interfere with the secure placement of

the seat. Secure with the enclosed tie-wraps so that

unit will not move.

Note: Although this device has been designed to significantly in-

crease your braking visibility, flash/strobe patterns may not be street

legal in your area. This device is not DOT approved.

Questions? Call us at: 1 (800) 382-1388

Custom Dynamics® Magic Strobes™ Brake Flasher

Installation Instructions

We thank you for purchasing the Custom Dynamics® Magic Strobes™

Brake Light Flasher! Our products utilize the latest technology and

high quality components to ensure you the most reliable service. We

offer one of the best warranty programs in the industry and we back

our products with excellent customer support, if you have questions

before or during installation of this product please call Custom

Dynamics® at 1(800) 382-1388.

Note: When installing the Magic Strobe™ on a 2010-2013

TriGlde®, the Magic-Strobes™ must be installed before the

stock brake-turn module.

Important: Module must be secured after installation. Find

safe area away from any moving parts and out of the way of

normal operation of the bike. Use the enclosed tie-wraps to

secure. Custom Dynamics® is not liable for damage as a

result of improperly securing or failing to secure the module.

Note: When using a Magic Strobes™ with a Smart Signal

Stabilizer™ or other load equalizer we recommend to install

the Magic Strobes™ after (towards the taillight) the Smart

Signal Stabilizer™ or load equalizer. (See Diagram)

Note: When using a Magic Brake Strobes™ with a Non Cus-

tom Dynamics® Run-Brake-Turn Controller, we recommend

the following:

-To flash Brake and turns, Install Magic Strobes™ Before Run

-Brake-Turn Controller. (See Diagram)

-To flash only the center taillight, install Magic Strobes™ After

Run-Brake-Turn Controller. (See Diagram)

Note: Do not Install any Custom Dynamics Magic Strobes™

unit with Custom Dynamics® Smart Triple Play® unit.

Important: Customers using this module with standard incan-

descent bulbs should use patterns 0-3 and 9 only. Any other

settings selected will result in diminished performance.

Caution: A stuck brake switch may cause this unit to over-

heat and fail. Unplug module immediately if this condition

occurs.

M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

ATTENTION

Please read all Information below before Installation

10-2017