Altronix eBridge Plus 1600F Manuale di installazione - Pagina 6

Sfoglia online o scarica il pdf Manuale di installazione per Ricevitore Altronix eBridge Plus 1600F. Altronix eBridge Plus 1600F 8. Ip and poe+ over coax solution, 16-port managed eoc receiver with integral poe+ switch

Stampa la pagina

Configuring eBridge1600F for Network Connection

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Please be sure to visit altronix.com for latest firmware and installation instructions

Factory Default Settings

• IP Address:

• User Name:

• Password:

1. Set the static IP address for the laptop to be used for programming to the same network IP address as the

eBridge1600F. The default address of the eBridge1600F is 192.168.168.168, E.I. 192.168.168.200.

2. Connect one end of the network cable to the network jack on the eBridge1600F and the other to the network

connection of the laptop.

3. Open a browser on the computer and enter "192.168.168.168" into the address bar. A dialog box

Authentication Required will appear requesting both user name and password.

Enter the default values here. Click on the button labeled Log In.

4. The status page of the eBridge1600F will appear. Click on the tab labeled Network Settings. This will open

the Network Setting screen. In this screen the MAC Address of the eBridge1600F module will be found

along with the Network Settings and Email Settings.

Network Settings:

In the IP Address Method field select the method that the IP Address for the eBridge1600F will be obtained

(STATIC or DHCP), then follow the appropriate steps.

Static:

A. IP Address: Enter the IP address assigned to the eBridge1600F by the network administrator.

B. Subnet Mask: Enter the Subnet of the network.

C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used. (gateway configuration

is required to properly receive emails from the device)

D. HTTP Port: Enter the HTTP port number assigned to the eBridge1600F module by the network administrator

to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and

unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with

LAN connections.

E. HTTPS Port: Enter the HTTPS port number assigned to the eBridge1600F module by the network

administrator to allow remote access and monitoring. The default inbound port setting is 443. Being encrypted

and more secure, HTTPS is highly recommended for remote access.

F. Click the button labeled Submit Network Settings. A dialog box will display "New network settings will

take effect after the server is rebooted". Click OK.

DHCP:

A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings.

A dialog box will display "New network settings will take effect after the server is rebooted". Click OK.

Next, click on the button labeled Reboot Server. After rebooting the eBridge1600F will be set in the DHCP

mode. The IP address will be assigned by the router when the eBridge1600F is connected to the network.

It is recommended to have the assigned IP Address reserved to ensure continued access

(see the network administrator).

B. Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.

C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.

D. HTTP Port: Enter the HTTP port number assigned to the eBridge1600F module by the network administrator

to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and

unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with

LAN connections.

E. HTTPS Port: Enter the HTTPS port number assigned to the eBridge1600F module by the network administrator

to allow remote access and monitoring. The default inbound port setting is 443. Being encrypted and more

secure, HTTPS is highly recommended for remote access.

F. Click the button labeled Submit Network Settings. A dialog box will display "New network settings will

take effect after the server is rebooted". Click OK.

Heartbeat Timer:

The heartbeat timer will send a trap message indicating that the unit is still connected and communicating.

Setting the Heartbeat Timer:

1. Click the button labeled Heartbeat Timer Setting.

2. Select the desired time between heartbeat messaging in the Days, Hours, Minutes and Seconds in

corresponding fields.

3. Click the button labeled Submit to save setting.

- 6 -

192.168.168.168

admin

eBridge1600F