DKM Motor Co., Ltd. FX3000 Manuale

Sfoglia online o scarica il pdf Manuale per Controllore DKM Motor Co., Ltd. FX3000. DKM Motor Co., Ltd. FX3000 2. Digital speed torque controller

Stampa la pagina

Operation/Parameter Setting Procedure

■ Operation setting procedure

After wiring, set as follows.

① Input AC power(Terminal CN1 #1, #2)

Display lights up(Rotation speed)

② Operation switch→RUN

Motor operates if the switch is

RUN position

③ Operation switch→STOP

Motor stops if the switch is

STOP position

④ Rotation direction setting

CW/CCW Switch

MOTOR

Clockwise

Counter Clockwise

at 'FWD'

at 'REV'

※ Caution

Please change rotation direction after the motor

completely stops.

⑤ Rotation speed setting

RPM changes if turn the dial.

If turning the dial slowly,

Decrease

Increase

RPM increases/decreases by 1r/min.

in speed

If turning the dial quickly, the speed

variation becomes large.

RPM DISPLAY

Setting data will change automatically

after 2 seconds.

If the power turns on again,

it operates with the final setting value.

※ Please refer to 'CW/CCW signal connection' in the

manual if operating RUN/STOP extemally.

Display/ Setting

■ Entire Transition Diagram

RPM display

Speed or Torque setting

with the dial

Mode Button

Parameter

PR01

DIAL

Mode Button

PRSF

PR07

※Speed Control P, I gain

- Parameter to determine the responsibility of speed control.

- Vibration and hunting phenomenon occurs if the value is too large.

■ Parameter setting procedure

After wiring, set as follows.

① Input AC power

Display lights up(Rotation speed)

② Select parameter mode

MODE Button

Enter into the parameter mode as pressing the

MODE button while motor is stop condition.

(STAND-BY)

"Pr01" appear at display

(Parameter mode)

③ Parameter Data

Turn the dial and choose the parameter

number which user wants to (Pr01~Pr07)

④ Change Parameter Data

ENTER

Press the dial(SET button) to enter

the parameter data.

PUSH

(Briefly)

CHANGE

DATA flickers and switches to changeable

status if pressing and holing the dial

(SET button) during 2 sec.

PUSH

(Hold-2sec.)

CHANGE

Data value will be changed and possible to

set the desired value if the dial is rotated

toward CW/CCW.

CW/CCW

(Roration)

COMPLETE

Data stop blinking and finish the setting when

pressing and holing the dial(SET button)

for 2 sec.

PUSH

(Hold-2sec.)

⑤ Operation Mode

MODE Button

'0' output at display

Press the MODE

(RPM)

button to enter the

(operation mode)

operation mode.

■ Parameter Contents

Parameter

Function Range Standard

Remark

NO. Display

Value

Time(second) to reach

Pr01 Acceleration

0~15.0

0.1

the set speed

Time

Rotation

0 : Clockwise

Pr02

0, 1

Direction

1 : Counterclockwise

Pr03

Gear Ratio 1~999

1.0

Input gear ratio

Control

0: Speed Control

Pr04

0, 1

Mode

1: Torque Control

Pr05

P Gain

0~255

100

Pr06

I Gain

0~255

Parameter

Reset when pressing and

Pr07

Reset

holding the SET button

Software

Display the

PrSF

Version

software version

DKM DIGITAL SPEED TORQUE CONTROLLER

FX3000 manual

We appreciate you for purchasing products of

DKM Motor co., Ltd. Before using the product you have

purchased, check to make sure that it is exactly

what you ordered. Then, please use it following the

instructions below.

SAFETY INFORMATION

Alerts declared in the manual are classified to Danger,

Warning and Caution by their criticality

DANGER indicates imminently hazardous situation which,

DANGER

if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which,

WARNING

if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which,

CAUTION

if not avoided, may result in minor or moderate injury.

DANGER

There is a danger of occurred shock in the input/output terminals so please

never let your body or conductive substance is touched.

WARNING

1. Do not put around the explosive atmosphere, gas to be burnt,

corrosive air, the location to be wet and combustibles.

If not, there will be the electric shock and the fire.

2. Installation, connection, operation, maintenance and diagnostic

operation should be carried out by the person who has expertise.

3. Use the product after turning off the power.

It may cause an electric shock.

4. The power cable and the lead wire should not be bent, pulled and

inserted by force. If not, the electric shock and the fire may occur.

5. In case of the motor and controlling unit are attached to the machine,

never touch with hand or connect with the earth. If not, the electric

shock may take place.

6. Within the 30 seconds after the power off, do not touch the output

terminal of the controlling unit. If not, the electric shock may occur

because of the residual volts.

CAUTION

The motor and the controlling unit should be used only by the

designated compounding. If not, the fire may occur.

Do not operate with the wet hands. The electric shock may occur.

In case of moving, do not catch the output shaft, connecting part or

the lead wire. There may be the injury by the drop.

The motor should be used after it is fixed tightly. If not, the injury

and/or the damage of the unit may occur.

Do not touch the rotating part (output shaft, cooling fan) in running.

It could be cause of injury.

If there are abnormal cases, turn off the power at once. If not, there

will be the electric shock, injury and the damage.

Do not touch the motor for a while, if the motor' s surface temperature

exceeds 90℃.

Be sure to set the switch STOP before connecting to the power.

Make sure to check the rotating direction before connecting the

machine. If not, the injury and/or the damage of the unit may occur.

10.

Use products only according to the specification of motor and

controlling unit. If not, there will be dangerous fire, electric shock,

injury and/or damage of the unit.

11.

Make sure to install the overload device because the protection device

is not attached to the motor. It is desirable to install other protection

devices other than overload protection device to prevent fire.

SPECIAL FEATURES

■ Possible to control speed and torque.

■ Possible to control the speed and torque of the motor simply by

connecting motor and control unit with connector and inputting the

AC terminal to the power source.

DKM Motor Co., Ltd.

Head Office / Factory

4F., Incheon Techpia Na-Bldg.,

Geobukro 17, Seo-gu, Incheon, Korea

Tel. +82.32.574.7788 Fax. +82.32.578.7787

www.dkmmotor.com

Head Office / Factory

4F., Incheon Techpia Na-Bldg.,

Geobukro 17, Seo-gu, Incheon, Korea

Tel. +82.32.574.7788 Fax. +82.32.578.7787

■ Display the current rotation speed(r/min) and torque(%).

■ Possible to control speed and torque easily with the front panel dial.

■ Possible to operate various functions by setting the parameter.

BEFORE USE

■ Check specifications which you ordered such as voltage,

output and so on.

■ Make sure a motor item whether the motor can be applicable with

DSKM controller.

■ Avoid the place in vibration, deep Impact, lots of dusty, inflammable

gas and corrosive gas.

■ Use ambient temperature(-10 ℃ ~ 40 ℃) and ambient humidity

(85% maximum and avoid direct sunlight, moisture and greasy place.

■ Install motor and controller as closely as possible. (within 2m)

CONTROLLER CODING SYSTEM

FX3000

006

Controller Model

OUTPUT

TYPE

S: Speed Motor

003: 3W

030: 30W

T: Torque Motor

006: 6W

040: 40W

010: 10W

060: 60W

015: 15W

090: 90W

020: 20W

120: 120W

025: 25W

180: 180W

■

Initial setting mode is speed control. Please change '0'(speed mode) to '1'

(torque motor) after selecting parameter 'Pr04'(control mode) if using torque motor.

Regarding changing method, please refer to 'Parameter setting procedure' and

'Display/Setting' in the manual.

Specifications

FX3000-□□

Model Name

Rated Voltage

1Ø AC 220~240V 50/60Hz ±10 %

Allowable Current

Below 6 A

Control Function

Speed Control, Torque Control

Control System

Phase Control

Speed

50Hz : 90~1400r/min

Control

60Hz : 90~1700r/min

Setting Range

Torque

0 ~ 100 %

Control

Speed Setting

Setting by Volume

±5%(Standard Value)

Speed Variation

Motor Output

3W~180W

-10C°~ 55C°

Ambient Temperature

35 ~ 85%RH (Without condensation)

Ambient Humidity

Over DC 500V 100MΩ

Insulation Resistance

(between power supply and external terminal)

AC 1500V 1minute

Dielectric Strength

(between power supply and external terminal)