Alvarado MSGX Manuale di istruzioni per l'installazione e la manutenzione - Pagina 4

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione e la manutenzione per Recinzioni e cancelli Alvarado MSGX. Alvarado MSGX 20. Full height maximum security gate

Stampa la pagina

Common Terms

•
Fail Safe - Gate unlocks in the event of power loss. The gate will relock when power is reapplied. All magnetic locks
are Fail Safe. Fail Safe electric strike locks are available as an option.
•
Fail Lock - Gate remains locked when power is removed (or lost). The gate will unlock only when both power and
an activation contact are supplied. All electric strike locks are Fail Lock unless otherwise specified.
Magnetic Locks are not available in Fail Lock mode.
•
Activation - Alvarado's gates require the use of a timed contact switch to lock and unlock. The gate will not
re-engage until the switch is released and the gate is closed.
•
Mesh Infill - The mesh infill is a diamond pattern steel mesh that is attached to the interior portion of the gate. The
purpose is to prevent persons from reaching through the gate. This component is available for all
models.
•
Microswitch Push Bar - This is an electrically operated mechanical push bar . If there is power loss, the bar will
•
Mechanical Push Bar - Mounted on the exit side, when the bar is pushed in the exit direction, the latching bolt is
•
Dead Bolt Lock - A keyed lockset that is used to lock the gate in a closed position. A key is required to unlock the
gate on either the entry or exit side of the gate.
•
Magnetic Lock - Magnetic lock offers up to 1200 pounds of holding force. Power (low-voltage 12VDC) is supplied
to the lock to energize the magnetic lock. When the gate is closed, the latch plate (mounted to
the gate) is held against the magnetic lock (mounted on the gate frame) when power is applied.
The gate is unlocked by removing power from the magnetic lock and the patron pulls the gate
open in the entry direction or pushes the gate open in the exit direction. This is standard only on
the MSGX and MSGX-PX models.
•
Electric Strike Lock - A lock where power (low-voltage 12VDC) is supplied to the lock to release the mechanism to
•
Universal Card Reader Mounting Plate - A mounting plate is attached to the latch post of the gate on the entry,
•
Push-To-Exit Remote Button Switch - A 3.15in square switch box assembly constructed of stainless steel with a
•
Magnetic Sensor Switch - A two piece switch magnet mounted on the gate and the latch post. It is used to monitor
Page 4
default to the condition specified for the lock in use. This component is not available for the
MSG or MSG-1 models.
mechanically retracted allowing the user to exit. This allows emergency exiting at any time
through the gate regardless of power conditions. This option is available only on: MSG-1,
MSGX-E, and MSGX-S models.
allow the gate to open. Power is then removed to allow the strike to be in the lock position.
This lock is standard on the MSGX-E and MSGX-S models.
exit, or both sides.The mounting plate is a universal style plate that an
additional device specific plate may be added in order to fit the reader that
is required. This option is available on: MSGX, MSGX-PX, MSGX-E, and
MSGX-S models.
DPDT (double pole double throw) push button switch. The switch is field
wired into the strike or magnetic lock power cable to unlock the gate from
a remote position such as a guard shack. This optional component
is available for: MSGX, MSGX-PX, MSGX-E, and MSGX-S models.
whether the gate is open or closed. The switch is a SPST (single pole single throw)
contact supplied with two lead in wires for field connection. This option is available for all
MSG models.
For Assistance: [email protected] +1 (909) 591-8431
MSG Installation and Maintenance Instructions
PUD1201R5-0