DO HEATING Austen Istruzioni per il fissaggio - Pagina 7

Sfoglia online o scarica il pdf Istruzioni per il fissaggio per Apparecchiature per il bagno DO HEATING Austen. DO HEATING Austen 8. Towel rail

Stampa la pagina
TOOLS REQUIRED FOR INSTALLATION

Installation Instructions

&
CORDLESS
CROSS POINT
&
SCREWDRIVER
SCREWDRIVER
(BIT PH2)
A
Air Vent (x1)
STEP LADDER
HAMMER
(FOR HIGH PRODUCTS)
Mounting elements, Decorative
B
2
90°
C
1
2
3
2
90°
1
IMPORTANT NOTE
•
•
•
•
•
1
2
METRIC RULER
HAMMER
INSTALLATION
1
1
ALLEN KEY
1-
Adjust the height of your radiator by
using a metric ruler.
2-
Set the location of your radiator as
2
desired, align with the ground by using
1
a spirit level and mark the position of
the wall mounting brackets.
INSTALLATION
1
2
www.hammamradiator.com.tr
1-
Drill holes (Ø 10 mm) into the spots
you have marked.
2-
Nail the wall plugs (E) in the holes by
using a hammer.
3
90°
3-
Screw the wall mounting brackets all
1
the way to the holes with the help of a
screwdriver.
1
1-
Adjust the height of your radiator by
using a metric ruler.
2-
Set the location of your radiator as
2
desired, align with the ground by using
1
a spirit level and mark the position of
the wall mounting brackets.
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the slots
on the mounting brackets (D), adjust the
distance between the wall and your
radiator then tighten the setscrews by
using an Allen key (M3).
Place your radiator at least 12.5 cm above the floor.
Provide insulation by wrapping PTFE tape on the treads before installing the valves.
1-
Drill holes (Ø 10 mm) into the spots
Apply silicone seal fluid to all treaded parts containing o-rings.
you have marked.
2-
Nail the wall plugs (E) in the holes by
Connect your radiator to the utilities after following all the installation steps in the manual.
using a hammer.
3
3-
After connecting to the utilities, do not forget to discharge the trapped air inside the
Screw the wall mounting brackets all
the way to the holes with the help of a
radiator before commissioning.
screwdriver.
STEP LADDER
ALLEN KEY
(FOR HIGH PRODUCTS)
1. Adjust the height of your radiator by using
2
a metric ruler.
2
2 Set the location of your radiator as desired, align
with the ground by using a spirit level and mark
the position of the wall mounting brackets.
90°
www.hammamradiator.com.tr
1-
Drill holes (Ø 10 mm) into the spots
you have marked.
2-
Nail the wall plugs (E) in the holes by
3
using a hammer.
1 Drill holes (Ø 10 mm) into the spots you
2
3-
have marked.
Screw the wall mounting brackets all
the way to the holes with the help of a
screwdriver.
2 Nail the wall plugs (E) in the holes by using
a hammer.
3 Screw the wall mounting brackets all the way
to the holes with the help of a screwdriver.
2
3
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the slots
on the mounting brackets (D), adjust the
1 Place your radiator into the wall mounting
distance between the wall and your
brackets (D).
radiator then tighten the setscrews by
using an Allen key (M3).
2 Insert the setscrews (F) into the slots on the
mounting brackets (D), adjust the distance
between the wall and your radiator then tighten
the setscrews by using an Allen key (M3).
1-
Drill holes (Ø 10 mm) into the spots
you have marked.
2
2-
Nail the wall plugs (E) in the holes by
3
using a hammer.
2
3-
Screw the wall mounting brackets all
the way to the holes with the help of a
screwdriver.
3
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the slots
on the mounting brackets (D), adjust the
distance between the wall and your
radiator then tighten the setscrews by
using an Allen key (M3).
3
1
2
3
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the slots
on the mounting brackets (D), adjust the
distance between the wall and your
1
radiator then tighten the setscrews by
using an Allen key (M3).
2
3
1
2
3
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the slots
on the mounting brackets (D), adjust the
distance between the wall and your
radiator then tighten the setscrews by
using an Allen key (M3).
www.hammamradiator.com.tr
1
2