DOEPFER Dark Energy II Informazioni tecniche aggiuntive - Pagina 6
Sfoglia online o scarica il pdf Informazioni tecniche aggiuntive per Sintetizzatore DOEPFER Dark Energy II. DOEPFER Dark Energy II 6.
Stampa la paginaFunction of the Jumpers and Trimming Potentiometers (Dark Energy II - Interface/Supply Board):
Name Function
JP1
Bus Connector
JP2
Gate bus
JP3
CV1 bus
JP4
Glide Option
JP5
Midi Out
JP6
Midi In
JP7/
Firmware Update
JP8
JP9
Reset/Program
JP10
Function of socket CV4
JP11
not used
JP12
Voltage range of CV2
A/B
(pitch bend)
JP13
Gate
JP14
Power Supply
JP15
CV2/CV3
P1
CV1 Scale
P2
Glide
DARK ENERGY II - Additional Technical Information – Page 6
Explanation
16 pin connection to voice board
(compatible to A-100 bus)
Connects the Gate line of JP1 to the gate output of the USB/Midi
interface
Connects the CV line of JP1 to the CV1 output of the USB/Midi
interface
This pin header can be used to install the glide option instead of the
jumper. For this a rotary potentiometer (1M log) has to connected to
the two pins. The glide option is available from your local
representative or dealer. It consists of a 1M potentiometer with Dark
Energy style knob and nut, 2-wire cable and 2-pin connector. All parts
are assembled, no soldering required.
This two pin connector is a Midi Output and can be used to daisy-
chain two DARK ENERGY via Midi Out/Midi In. For this the Midi Out
of the first device has to be connected to Midi In of the second device
via a suitable two wire cable. The first unit has to be set into the
"Stack Mode" (details in the user's guide). The left pin of JP5 is GND,
the right pin is Midi Out
This two pin connector in a Midi Input and can be used to daisy-chain
two DARK ENERGY via Midi Out/Midi In. For this the Midi Out of the
first device has to be connected to Midi In of the second device via a
suitable two wire cable. The left pin of JP6 is GND, the right pin is
Midi In.
To these single row pin headers several jumpers can be installed in
different ways. In the standard mode two jumpers have to be installed
as shown in the sketch.
Only if the firmware of the device has to be updated the positions of
the jumpers have to be changed. As soon as a new firmware is
available the corresponding information will be published.
This jumper is used only during the programming in the factory. It has
to remain always in the position shown in the sketch !
With this jumper one can select if the socket labelled "CV4" outputs
really CV4 or if it is used as a second audio output (in parallel to the
audio output socket at the front panel). In the upper position it works
as CV4 (factory setting), in the lower position as audio output.
this pin header is not assembled (it would be on the bottom side of
the pcb)
These jumpers are used to define the output voltage range of CV2
(pitch bend):
JP12A installed: CV2 range ~ – 2.5...+2.5V (symmetrical around 0V)
JP12B installed: CV2 range ~ 0...+5V (only positive voltage)
Only one of two jumpers has to be installed, never both !
Gate output of the interface for optional expansions
power supply connector for optional expansions, from left to right:
•
-12V
•
GND
•
+12V
max. current 20 mA !
CV2/CV3 outputs for optional expansions, from left to right:
•
CV2
•
CV3
adjusts the 1V/octave characteristics of CV1
optional rotary potentiometer for glide function (portamento) of CV1,
is connected to JP4 (instead of the jumper), recommended value: 1M
logarithmic (A1M)
Factory default
connected to
voice board via
ribbon cable
installed
installed
installed
open
open
two jumpers
installed as
shown in the
sketch
installed (left
position)
installed (upper
position)
not used
JP12A installed
(-2,5...+2,5V)
-
-
-
adjusted to
1.00V/octave
not installed